Component guide · Beginner · 3 min read
XH-M229 ATX Power Supply Breakout Board

Turn a PC PSU into a Bench Supply
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The XH-M229 board plugs into the 24-pin connector of a PC power supply and brings 3.3 V, 5 V and 12 V out to screw terminals with a power switch. It turns an old ATX supply into a high-current bench supply for robots, LED strips and 3D printer parts. The supply can deliver tens of amps, so fuse each output.
Key specs at a glance
- Connector
- 24-pin ATX
- Outputs
- 3.3 V, 5 V, 12 V, -12 V, 5 V standby
- Switch
- Power on (PS_ON)
- Current
- Depends on PSU, often 20 A on 12 V
- Indicators
- LED for power
- Terminals
- Screw terminals
What the XH-M229 ATX power supply breakout is
The XH-M229 is a breakout board for a standard PC (ATX) power supply. It plugs into the 24-pin connector and brings the 3.3, 5 and 12 V rails out to screw terminals with an on/off switch.
Some older supplies need a minimum load on 5 V to regulate 12 V properly. The board may include a load resistor; if not, add a 10 ohm 10 W resistor on 5 V.
Fuse each output you use. A short on a PC supply can melt wires before it trips.
XH-M229 ATX power supply breakout pinout
The pins on the XH-M229 ATX power supply breakout and what each one does.
| Pin | Function |
|---|---|
| 24-pin socket | From PSU |
| 3.3V, 5V, 12V, GND | Outputs |
| Switch | PS_ON |
- 24-pin socket
- From PSU
- 3.3V, 5V, 12V, GND
- Outputs
- Switch
- PS_ON
Wiring the XH-M229 ATX power supply breakout
Connect the XH-M229 ATX power supply breakout like this.
| XH-M229 ATX power supply breakout pin | Typical use | Second load |
|---|---|---|
| 12V | Robot or LED strip via fuse | Same |
| 5V | Raspberry Pi via fuse | Same |
- 12V
- Typical use:
- Robot or LED strip via fuse
- Second load:
- Same
- 5V
- Typical use:
- Raspberry Pi via fuse
- Second load:
- Same
Example code
A minimal sketch to check the part works.
Plug the ATX connector, switch on, measure each output,
then connect loads through fuses.Setup and tuning
add a 5 to 10 A fuse on each output you use; a PC supply can deliver 20 A or more.
keep the power supply fan and vents clear.
some older supplies need a small load on 5 V to regulate 12 V properly.
use wires rated for the current at each terminal.
never open the power supply; it has mains voltage and charged capacitors inside.
What you need
Shop this list2 of 2 found in our store · ₹364
XH-M229 ATX Power Supply Breakout: the part this guide coversXH-M229 ATX Power Supply Breakout₹187
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- Bench power supply: adjustable and current limited.
- Robot power planning.
Common mistakes to avoid
- Using it without fuses.
- Opening the power supply case.
- Ignoring the minimum load on older supplies.
- Using thin wires on the 12 V terminal.
Frequently asked questions
Is the voltage adjustable on the XH-M229?
No. It gives the fixed ATX rails: 3.3 V, 5 V, 12 V, −12 V and 5 V standby.
Does it limit current?
Only through the power supply's own protection, so add fuses on each output.
Will any ATX power supply work?
Any supply with a 24-pin ATX connector works.
What is the 5VSB terminal?
5 V standby, which stays on whenever the supply is plugged in, even when switched off.
Is it safe to use?
Yes, if each output is fused and the power supply case stays closed.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
