Raspberry Pi Pico weather display (MicroPython)
Your first MicroPython project: temperature and humidity on an OLED.
Shop by category
Shop all componentsWhen produce spoils in a cold store, the question is always why. This logger records the store temperature from a probe among the crates, the humidity, and the door state every minute. The file shows whether the door was left open, the cooling failed, or the store was simply overloaded.
Tick anything you already have and the total updates.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Glass switch whose contacts close when a magnet is near.
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Stores readings on a microSD card as a CSV file you can open in Excel or Google Sheets.
Follow the colours: red is power, dark grey is ground, blue is a signal.
mega_cold_store_door_logger.inoVerify & upload in Electrolark// Cold store temperature and door logger on an Arduino Mega
// Geekobot project library · board: Arduino Mega 2560
// Wiring diagram, parts list and build steps: Geekobot project page "mega-cold-store-door-logger"
#include <OneWire.h>
#include <DallasTemperature.h>
#include <DHT.h>
#include <Wire.h>
#include <RTClib.h>
#include <SPI.h>
#include <SD.h>
// ---- pins ----
const uint8_t ONEWIRE_PIN = 22;
const uint8_t DHT_PIN = 23;
const uint8_t REED_PIN = 24;
const uint8_t SD_CS = 53;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
DHT dht(DHT_PIN, DHT22);
RTC_DS3231 rtc;
// ---- latest readings ----
float probeC = 0;
float tempC = 0;
float humidity = 0;
bool doorOpen = false;
const unsigned long LOG_EVERY_MS = 60000UL; // one row per minute
unsigned long lastLog = 0;
bool cardOk = false;
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void writeRow() {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (!f) { Serial.println(F("Write failed")); return; }
DateTime t = rtc.now();
char stamp[20];
snprintf(stamp, sizeof(stamp), "%04d-%02d-%02d,%02d:%02d:%02d", t.year(), t.month(), t.day(), t.hour(), t.minute(), t.second());
f.print(stamp);
f.print(',');
f.print(probeC, 1);
f.print(',');
f.print(tempC, 1);
f.print(',');
f.print(humidity, 0);
f.print(',');
f.print(doorOpen);
f.println();
f.close();
}
void setup() {
Serial.begin(115200);
probes.begin();
dht.begin();
pinMode(REED_PIN, INPUT_PULLUP);
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
cardOk = SD.begin(SD_CS);
Serial.println(cardOk ? F("SD card ready") : F("SD card not found"));
if (cardOk && !SD.exists("LOG.CSV")) {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (f) { f.println(F("date,time,Probe(C),Temp(C),Humidity(%),Door open")); f.close(); }
}
}
void loop() {
if (millis() - lastLog < LOG_EVERY_MS && lastLog != 0) return;
lastLog = millis();
probeC = readProbeC();
tempC = dht.readTemperature();
humidity = dht.readHumidity();
doorOpen = digitalRead(REED_PIN) == HIGH;
Serial.print(F("Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.print(F(", Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", Humidity="));
Serial.print(humidity, 0);
Serial.print(F("%"));
Serial.print(F(", Door open="));
Serial.print(doorOpen ? F("yes") : F("no"));
Serial.println();
if (cardOk) writeRow();
}
The sketch above runs here on a simulated Arduino Mega. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
Bring the magnet within 1 cm and align it parallel to the glass body.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Check the card is FAT32, fully inserted, and CS is on the pin in the sketch.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Use a 5 V USB phone charger or a power bank into the board's USB port.
10 parts: MEGA 2560 R3 Dev Board with ATmega2560 & CH340G, DS18B20 Waterproof Temperature Probe – 1m Cable, DHT22 Temperature & Humidity Sensor, Y213 Reed Switch Normally Open (glass), DS3231 Precision RTC Module with EEPROM, DFRobot Fermion MicroSD Card Module – SPI, Resistor Assortment Kit (30 Values), microSD Memory Card Class 10 (16GB), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 11 steps.
No. This page has the complete, tested code (mega_cold_store_door_logger.ino). Install these libraries first: OneWire, DallasTemperature, DHT sensor library, Adafruit Unified Sensor, RTClib and SD.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹2,307 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Pull-up resistors and reed switches; Real-time clocks and backup batteries; SPI devices and CSV logging; Single-wire digital sensors and why some sensors need slow polling.
Ideas that reuse this build: Cold room temperature logger and Cold storage door alarm. They are listed under Take it further on this page.
Your first MicroPython project: temperature and humidity on an OLED.
A web page with ON and OFF buttons that switches a relay over Wi-Fi.
A warm ring light that fades up at dusk and down at dawn.
Turn a Pi and a touchscreen into a home command centre with a clock and to-do list.
Learning project. Check every circuit and the datasheet of each part before you power it up.
SD card ready Probe=26.0C, Temp=26.9C, Humidity=55%, Door open=yes Probe=26.0C, Temp=27.0C, Humidity=55%, Door open=yes
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.