Raspberry Pi Pico weather display (MicroPython)
Your first MicroPython project: temperature and humidity on an OLED.
Shop by category
Shop all componentsHeat, noise and stale air are what make study hard. The panel puts all four numbers on one OLED on the wall, with the light state in the Serial Monitor. Students can see for themselves when the room needs a window open or a quieter table.
This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed.
Tick anything you already have and the total updates.
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Heated sensor that responds to ammonia, CO₂, alcohol, smoke and benzene.
Light-dependent resistor with a comparator: its output flips when the light falls below the level set by the trimmer.
Follow the colours: red is power, dark grey is ground, blue is a signal.
mega_library_classroom_monitor.inoVerify & upload in Electrolark// Library and classroom comfort panel on an Arduino Mega
// Geekobot project library · board: Arduino Mega 2560
// Wiring diagram, parts list and build steps: Geekobot project page "mega-library-classroom-monitor"
#include <DHT.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t DHT_PIN = 22;
const uint8_t MIC_PIN = A0;
const uint8_t AIR_PIN = A1;
const uint8_t LDR_PIN = 23;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
DHT dht(DHT_PIN, DHT22);
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float tempC = 0;
float humidity = 0;
int soundPct = 0;
int airPct = 0;
bool dark = false;
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
const char* statusText = "OK";
int readSoundLevel() {
// peak-to-peak amplitude over a 50 ms window
unsigned long start = millis();
int lo = ADC_MAX, hi = 0;
while (millis() - start < 50) {
int v = analogRead(MIC_PIN);
if (v < lo) lo = v;
if (v > hi) hi = v;
}
return (int)((hi - lo) * 100L / ADC_MAX);
}
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Room comfort"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 14);
oled.print(F("Temp: "));
oled.print(tempC, 1);
oled.print(F(" C"));
oled.setCursor(0, 24);
oled.print(F("Humidity: "));
oled.print(humidity, 0);
oled.print(F("%"));
oled.setCursor(0, 34);
oled.print(F("Sound: "));
oled.print(soundPct);
oled.print(F("%"));
oled.setCursor(0, 44);
oled.print(F("Air: "));
oled.print(airPct);
oled.print(F("%"));
oled.setCursor(0, 56);
oled.print(statusText);
oled.display();
}
void setup() {
Serial.begin(115200);
dht.begin();
pinMode(LDR_PIN, INPUT);
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
tempC = dht.readTemperature();
humidity = dht.readHumidity();
soundPct = readSoundLevel();
airPct = (int)(analogRead(AIR_PIN) * 100L / ADC_MAX);
dark = digitalRead(LDR_PIN) == HIGH;
statusText = (!isnan(tempC) && !isnan(humidity)) ? "OK" : "Sensor error";
Serial.print(F("Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", Humidity="));
Serial.print(humidity, 0);
Serial.print(F("%"));
Serial.print(F(", Sound="));
Serial.print(soundPct);
Serial.print(F("%"));
Serial.print(F(", Air="));
Serial.print(airPct);
Serial.print(F("%"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Mega. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
Turn the module trimmer to increase gain, or move the mic closer to the sound.
Normal: the heater needs a few minutes to settle. Wait before calibrating the threshold.
Some modules invert DO. Change == HIGH to == LOW in the code.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: MEGA 2560 R3 Dev Board with ATmega2560 & CH340G, DHT22 Temperature & Humidity Sensor, Analog Sound Sensor Microphone Module, Winsen MQ135 Air Quality Gas Sensor, Digital LDR Light Sensor Module – LM393, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 11 steps.
No. This page has the complete, tested code (mega_library_classroom_monitor.ino). Install these libraries first: DHT sensor library, Adafruit Unified Sensor, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,706 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Analog sensors, ADCs and warm-up drift; Drawing text on an I²C display; Sampling a waveform and measuring amplitude; Single-wire digital sensors and why some sensors need slow polling; Thresholds set in hardware vs software.
This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed.
Ideas that reuse this build: Class quiet library and Air quality ring. They are listed under Take it further on this page.
Your first MicroPython project: temperature and humidity on an OLED.
A web page with ON and OFF buttons that switches a relay over Wi-Fi.
A warm ring light that fades up at dusk and down at dawn.
Turn a Pi and a touchscreen into a home command centre with a clock and to-do list.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Temp=26.9C, Humidity=55%, Sound=10%, Air=30%
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.