Raspberry Pi Pico weather display (MicroPython)
Your first MicroPython project: temperature and humidity on an OLED.
Shop by category
Shop all componentsCloudy water, warm water and a slow trickle all tell you something. The turbidity sensor measures clarity, the probe measures temperature and the flow sensor measures the rate. A rural water committee or a school science club can see the effect of a filter by comparing before and after.
Not a drinking water test. Clarity and temperature do not show bacteria or chemicals.
Tick anything you already have and the total updates.
Shines light through the water gap and measures how much gets through.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
A small turbine with a magnet and Hall sensor: each turn sends a pulse, and pulses per second give the flow rate.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
mega_water_quality_panel.inoVerify & upload in Electrolark// Water quality and tank panel on an Arduino Mega
// Geekobot project library · board: Arduino Mega 2560
// Wiring diagram, parts list and build steps: Geekobot project page "mega-water-quality-panel"
#include <OneWire.h>
#include <DallasTemperature.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
#if defined(ESP32) || defined(ESP8266)
#define IRAM_SAFE IRAM_ATTR
#else
#define IRAM_SAFE
#endif
// ---- pins ----
const uint8_t TURB_PIN = A0;
const uint8_t ONEWIRE_PIN = 22;
const uint8_t FLOW_PIN = 2;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
volatile unsigned long flowPulses = 0;
unsigned long lastFlowMs = 0;
float litresTotal = 0;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
int clarityPct = 0;
float probeC = 0;
float flowLpm = 0;
float litres = 0;
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
const char* statusText = "OK";
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void IRAM_SAFE onFlowPulse() { flowPulses++; }
float readFlowLpm() {
unsigned long now = millis();
float secs = (now - lastFlowMs) / 1000.0f;
if (secs <= 0) return 0;
noInterrupts();
unsigned long p = flowPulses;
flowPulses = 0;
interrupts();
lastFlowMs = now;
float lpm = (p / secs) / 7.5f; // YF-S201: about 7.5 pulses per second per L/min
litresTotal += lpm * secs / 60.0f;
return lpm;
}
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Clarity "));
lcd.print(clarityPct);
lcd.print(F("%"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(F("Prob "));
lcd.print(probeC, 1);
lcd.print(F(" C"));
lcd.print(F(" "));
lcd.print(statusText);
lcd.print(F(" "));
}
void setup() {
Serial.begin(115200);
probes.begin();
pinMode(FLOW_PIN, INPUT_PULLUP);
attachInterrupt(digitalPinToInterrupt(FLOW_PIN), onFlowPulse, RISING);
lastFlowMs = millis();
lcd.init();
lcd.backlight();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
clarityPct = (int)(analogRead(TURB_PIN) * 100L / ADC_MAX);
probeC = readProbeC();
flowLpm = readFlowLpm();
litres = litresTotal;
statusText = (probeC > -100) ? "OK" : "Sensor error";
Serial.print(F("Clarity="));
Serial.print(clarityPct);
Serial.print(F("%"));
Serial.print(F(", Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.print(F(", Flow="));
Serial.print(flowLpm, 1);
Serial.print(F("L/min"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Mega. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Shade the sensor gap; stray light adds to the reading.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
Check the arrow direction and that the signal wire is on an interrupt-capable pin.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: MEGA 2560 R3 Dev Board with ATmega2560 & CH340G, Asair AZDM01 Turbidity Sensor Module – Analog, DS18B20 Waterproof Temperature Probe – 1m Cable, YF-S201 Water Flow Sensor 1–30 L/min, LCD1602 16x2 Character LCD (blue, with I2C adapter), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (mega_water_quality_panel.ino). Install these libraries first: OneWire, DallasTemperature and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,674 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Character displays and I²C backpacks; Interrupts and counting pulses; Optical sensing and calibration references.
Not a drinking water test. Clarity and temperature do not show bacteria or chemicals.
Ideas that reuse this build: Water clarity tester and Wi-Fi water usage meter. They are listed under Take it further on this page.
Your first MicroPython project: temperature and humidity on an OLED.
A web page with ON and OFF buttons that switches a relay over Wi-Fi.
A warm ring light that fades up at dusk and down at dawn.
Turn a Pi and a touchscreen into a home command centre with a clock and to-do list.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Clarity=29%, Probe=26.0C, Flow=0.0L/min
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.