Raspberry Pi Pico weather display (MicroPython)
Your first MicroPython project: temperature and humidity on an OLED.
Shop by category
Shop all componentsFumes from soldering and painting, noise from grinders and saws, heat and damp all affect the people working in a small workshop. The OLED shows all four readings, so everyone can see when to open the shutter, put on ear defenders or switch on the extractor.
This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed.
Tick anything you already have and the total updates.
Heated sensor that responds to ammonia, CO₂, alcohol, smoke and benzene.
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Follow the colours: red is power, dark grey is ground, blue is a signal.
mega_workshop_environment_panel.inoVerify & upload in Electrolark// Workshop air, noise and climate panel on an Arduino Mega
// Geekobot project library · board: Arduino Mega 2560
// Wiring diagram, parts list and build steps: Geekobot project page "mega-workshop-environment-panel"
#include <DHT.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t AIR_PIN = A0;
const uint8_t MIC_PIN = A1;
const uint8_t DHT_PIN = 22;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
DHT dht(DHT_PIN, DHT22);
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
int airPct = 0;
int soundPct = 0;
float tempC = 0;
float humidity = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
const char* statusText = "OK";
int readSoundLevel() {
// peak-to-peak amplitude over a 50 ms window
unsigned long start = millis();
int lo = ADC_MAX, hi = 0;
while (millis() - start < 50) {
int v = analogRead(MIC_PIN);
if (v < lo) lo = v;
if (v > hi) hi = v;
}
return (int)((hi - lo) * 100L / ADC_MAX);
}
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Workshop"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 14);
oled.print(F("Air: "));
oled.print(airPct);
oled.print(F("%"));
oled.setCursor(0, 24);
oled.print(F("Sound: "));
oled.print(soundPct);
oled.print(F("%"));
oled.setCursor(0, 34);
oled.print(F("Temp: "));
oled.print(tempC, 1);
oled.print(F(" C"));
oled.setCursor(0, 44);
oled.print(F("Humidity: "));
oled.print(humidity, 0);
oled.print(F("%"));
oled.setCursor(0, 56);
oled.print(statusText);
oled.display();
}
void setup() {
Serial.begin(115200);
dht.begin();
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
airPct = (int)(analogRead(AIR_PIN) * 100L / ADC_MAX);
soundPct = readSoundLevel();
tempC = dht.readTemperature();
humidity = dht.readHumidity();
statusText = (!isnan(tempC) && !isnan(humidity)) ? "OK" : "Sensor error";
Serial.print(F("Air="));
Serial.print(airPct);
Serial.print(F("%"));
Serial.print(F(", Sound="));
Serial.print(soundPct);
Serial.print(F("%"));
Serial.print(F(", Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", Humidity="));
Serial.print(humidity, 0);
Serial.print(F("%"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Mega. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Normal: the heater needs a few minutes to settle. Wait before calibrating the threshold.
Turn the module trimmer to increase gain, or move the mic closer to the sound.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: MEGA 2560 R3 Dev Board with ATmega2560 & CH340G, Winsen MQ135 Air Quality Gas Sensor, Analog Sound Sensor Microphone Module, DHT22 Temperature & Humidity Sensor, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (mega_workshop_environment_panel.ino). Install these libraries first: DHT sensor library, Adafruit Unified Sensor, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,675 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Analog sensors, ADCs and warm-up drift; Drawing text on an I²C display; Sampling a waveform and measuring amplitude; Single-wire digital sensors and why some sensors need slow polling.
This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed.
Ideas that reuse this build: Workshop dust alarm and Workshop sound exposure meter. They are listed under Take it further on this page.
Your first MicroPython project: temperature and humidity on an OLED.
A web page with ON and OFF buttons that switches a relay over Wi-Fi.
A warm ring light that fades up at dusk and down at dawn.
Turn a Pi and a touchscreen into a home command centre with a clock and to-do list.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Air=29%, Sound=10%, Temp=27.0C, Humidity=55% Air=30%, Sound=10%, Temp=27.0C, Humidity=55%
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.