Component guide · Beginner · 3 min read
1S Li-ion Protection Board (3.7V, DW01 + 8205A)

Wiring and Limits
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A 1S protection board sits between a single 3.7 V Li-ion cell and the load. It cuts off if the cell is over-charged (about 4.25 V), over-discharged (about 2.5 to 3.0 V), shorted or overloaded. It does not charge the cell; pair it with a charger. Versions range from 2 to 5 A or more, set by the MOSFETs on the board.
Key specs at a glance
- Cells
- 1 x Li-ion or LiPo, 3.7 V
- Over-charge cut
- About 4.25 to 4.3 V
- Over-discharge cut
- About 2.5 to 3.0 V
- Current
- 2 A to 5 A versions
- Chips
- DW01 protection IC with 8205A MOSFETs (typical)
- Pads
- B+, B-, P+, P-
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
What the 1S Li-ion protection board is
A 1S protection board is a small circuit that sits on one lithium cell and disconnects it when the voltage, current or a short goes outside safe limits. It protects the cell; it does not charge it.
B+ and B- go to the cell. P+ and P- go to the load and charger. The board switches the negative side, so P- is not the same as B-; never join them.
Protection limits are a last resort. Set your own low-voltage cut-off in code at about 3.3 V for longer cell life.
1S Li-ion protection board pinout
The pins on the 1S Li-ion protection board and what each one does.
| Pin | Function |
|---|---|
| B+ / B- | Cell terminals |
| P+ / P- | Pack output to load and charger |
- B+ / B-
- Cell terminals
- P+ / P-
- Pack output to load and charger
Wiring the 1S Li-ion protection board
Connect the 1S Li-ion protection board like this.
| 1S Li-ion protection board pin | 18650 build | LiPo build |
|---|---|---|
| B+ / B- | 18650 cell | LiPo pouch |
| P+ / P- | Charger output and load | Boost converter input |
- B+ / B-
- 18650 build:
- 18650 cell
- LiPo build:
- LiPo pouch
- P+ / P-
- 18650 build:
- Charger output and load
- LiPo build:
- Boost converter input
Example code
A minimal sketch to check the part works.
const float LOW_V = 3.3; // warn below this cell voltage
void setup() { Serial.begin(9600); }
void loop() {
float v = analogRead(A0) * 5.0 / 1023 * 2; // 2:1 divider
Serial.println(v);
if (v < LOW_V) Serial.println("Battery low, shut down");
delay(2000);
}Setup and tuning
tin the board pads first and keep the cell cool; spot-weld nickel strip to the cell where possible.
choose a board rated above your peak load, such as 5 A for small motors.
after a cut-off or first assembly, connect a charger briefly to reset the board.
set your code to shut down at about 3.3 V; the board's 2.5 to 3.0 V cut-off is a last resort.
B+ and B− go to the cell, P+ and P− to the load and charger; never link B− to P−.
What you need
Shop this list5 of 5 found in our store · ₹16,41,048
1S Li-ion Protection Board (3.7V): the part this guide covers1S Li-ion Protection Board (3.7V)₹16
18650 Li-ion rechargeable cell: the cell to charge or protect18650 Li-ion Rechargeable Cell₹119Closest match, check the specs
18650 battery holder: to hold the cellBattery Holder₹45
TP4056 1A Li-ion charger module with protection: a simple 1-cell chargerTP4056 1A Li-ion Charger Module with Protection₹19
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- TP4056 charger: charge plus protection on one board.
- BMS boards: multi-cell packs.
- Lithium batteries.
Common mistakes to avoid
- Joining B− and P−, which bypasses the protection.
- Using it as a charger.
- Choosing a board rated below the load's peak current.
- Relying on the board's cut-off instead of a higher cut-off in code.
Frequently asked questions
Does a 1S protection board charge the battery?
No. It only protects the cell. Use a TP4056, TP5000 or another CC/CV charger to charge it.
Why is there no output from my protection board?
It has tripped on over-discharge or a short. Connect a charger for a moment to reset it.
Can I use it with a LiPo cell?
Yes. Single-cell LiPo and Li-ion cells use the same 4.2 V limits.
Can I use it with LiFePO4 cells?
No. LiFePO4 cells need lower limits (about 3.65 V full), so use a board made for LFP.
Which current rating should I choose?
Pick a rating above your peak current. Motors and servos need the 5 A versions.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

