How-to · Advanced · 3 min read
4G LTE Modules for IoT
SIM7600, A7672 and EC200U With Arduino and ESP32
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A 4G LTE module gives a microcontroller mobile data and sometimes GPS. Pick a variant with the bands your operators use, power it from a supply that can deliver 2 A peaks, fit the LTE antenna, and talk to it with AT commands over UART. Cat-1 modules such as the A7672 and EC200U are cheaper and lower power than Cat-4 types.
Key specs at a glance
- SIM7600 series
- LTE Cat-1 to Cat-4 depending on the variant (see the product page), GNSS, 2G/3G fallback on some regions
- A7672 / EC200U
- LTE Cat-1, moderate speed, lower cost and power
- Supply
- 3.4 to 4.2 V on the module; peaks near 2 A, so use a strong supply and a large capacitor
- Interface
- UART with AT commands, USB, sometimes SPI
- SIM
- Micro or nano SIM with a data plan and an active APN
- Antennas
- Main LTE antenna, optional GNSS antenna
Choosing a module
The most important point is that the module supports the bands your local operators use. Most modules ship in regional variants with different band lists, so match the variant to your country and operator. Newer networks may have switched off 2G or 3G, so a module that relies on them will fail.
| Type | Speed | Strengths | Notes |
|---|---|---|---|
| SIM7600 series | Cat-1 to Cat-4 (varies by variant) | Widely used, GNSS, many hat and breakout boards | Heavier on power; many variants |
| A7672 series | Cat-1 | Cost-effective replacement for 2G modules | Check band list for your region |
| Quectel EC200U | Cat-1 | Compact, GNSS, good documentation | Needs a strong 3.8 V supply |
| SIM800 / SIM900 | 2G GSM/GPRS | Simple and cheap | Only works where 2G is still on; see SIM800L |
- SIM7600 series
- Speed:
- Cat-1 to Cat-4 (varies by variant)
- Strengths:
- Widely used, GNSS, many hat and breakout boards
- Notes:
- Heavier on power; many variants
- A7672 series
- Speed:
- Cat-1
- Strengths:
- Cost-effective replacement for 2G modules
- Notes:
- Check band list for your region
- Quectel EC200U
- Speed:
- Cat-1
- Strengths:
- Compact, GNSS, good documentation
- Notes:
- Needs a strong 3.8 V supply
- SIM800 / SIM900
- Speed:
- 2G GSM/GPRS
- Strengths:
- Simple and cheap
- Notes:
- Only works where 2G is still on; see SIM800L
Power is the usual problem
LTE modules draw short bursts of current up to about 2 A when transmitting. A weak supply makes the module reset or drop off the network. Use a dedicated 3.8 to 4.2 V supply or a buck converter rated 3 A, add a 470 to 1000 µF capacitor close to the module, and keep wires short and thick. Do not power it from the Arduino or ESP32 3.3 V pin. See DC-DC converters.
Wiring and first test
Connect module TX to the microcontroller RX, module RX to TX, and join the grounds. Use a logic level shifter if the module is 1.8 V logic. Insert the SIM, attach the antenna and power the module. Send AT commands at the module's baud rate (often 115200) and check the replies below.
// Module TX -> GPIO16 (RX2), module RX -> GPIO17 (TX2)
void setup() {
Serial.begin(115200);
Serial2.begin(115200, SERIAL_8N1, 16, 17);
delay(3000);
const char* cmds[] = { "AT", "AT+CPIN?", "AT+CSQ", "AT+CREG?", "AT+COPS?" };
for (auto c : cmds) {
Serial2.println(c);
delay(800);
while (Serial2.available()) Serial.write(Serial2.read());
}
}
void loop() {}Getting online
- 1
AT+CPIN?should return READY, which means the SIM is unlocked. - 2
AT+CSQshows signal strength; 10 to 31 is usable, 99 means none. - 3
AT+CREG?orAT+CEREG?should report registered on the home or roaming network. - 4Set your APN with the AT command from the module manual, then open the data connection and use the module's HTTP, MQTT or socket commands.
- 5For production, use a library such as TinyGSM, which wraps these commands. For MQTT over cellular see MQTT.
Try it: Battery life calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Powering the module from the microcontroller's 3.3 V pin.
- Buying a variant without your operator's bands.
- Forgetting the antenna, which can damage the transmitter.
- Using a SIM without an active data plan or the right APN.
- Relying on 2G or 3G fallback that has been switched off.
Frequently asked questions
What is the difference between Cat-1 and Cat-4?
Cat-4 reaches higher speeds. Cat-1 is slower but cheaper and enough for sensor data, tracking and MQTT.
Can I use a normal phone SIM?
Often yes, but check that the SIM allows data on IoT devices and is not locked to a phone.
Why does the module keep rebooting?
Most often the supply cannot deliver the current peaks. Add a larger capacitor and a better regulator.
Does it include GPS?
Many SIM7600 and EC200U variants include GNSS; check the exact part number and fit the GNSS antenna.
Is AT+CSQ 99 a problem?
Yes, it means no signal. Check the antenna, SIM, bands and coverage.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
- SIMCom SIM7600 hardware design and AT command manual
- Quectel EC200U hardware design
- TinyGSM library documentation
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




