Component guide · Beginner · 4 min read
Classic MCU Boards

Amotech Labs AT89S52 8051 Development Boards with USB-C and ISP, ATmega16/32 Minimum System Board, LPC2148 ARM7 Module, ATtiny88 Nano-Compatible Board and Digispark ATtiny85 USB Boards
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These boards cover the microcontrollers taught in many engineering syllabuses. The AT89S52 8051 boards are for 8051 labs in C or assembly, with USB-C power and an ISP programmer on some. ATmega16/32 boards suit AVR courses, and the LPC2148 module is the classic ARM7 teaching board. ATtiny88 and Digispark ATtiny85 are tiny, cheap Arduino-compatible boards for small gadgets.
Key specs at a glance
- 8051
- AT89S52, 8KB flash, 11.0592 MHz crystal
- ATmega16/32
- 16 or 32KB flash, 40-pin DIP
- LPC2148
- ARM7TDMI, 512KB flash, USB
- ATtiny88
- 8KB flash, Nano footprint
- Digispark
- ATtiny85, micronucleus USB bootloader
- Tools
- Keil or SDCC (8051), Microchip Studio/avr-gcc, Keil or GCC (ARM7), Arduino IDE
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Amotech Labs 8051 Development Board w/ AT89S52 & USB-C₹885
Option 2Amotech Labs 8051 Development Board w/ USB-C & ISP Programmer₹1,375
Option 3Amotech Labs 8051 Mini Development Board w/ AT89S52 MCU₹590
Option 4ATmega16/32 ISP AVR Minimum System Development Board₹309
Option 5LPC2148 ARM7 Development Module Board₹4,265
Option 6ATTINY88 Development Board 16MHz, NANO V3.0 Compatible, Unsoldered₹237
What the 8051, ATtiny, ATmega16/32 and LPC2148 ARM7 development boards for labs and learning is
These boards carry classic teaching microcontrollers, the 8051, AVR ATmega and ARM7 LPC2148, on ready boards with power, a crystal and programming headers for lab work.
For 8051, write C in Keil uVision or the free SDCC compiler and program the AT89S52 with an ISP programmer (USBasp or the on-board one) using a tool such as ProgISP or avrdude with an 8051 config. Use the 11.0592 MHz crystal for standard baud rates.
LPC2148 programs over its UART bootloader with Flash Magic: hold P0.14 low at reset. Digispark boards install through the Digistump board package, and you plug them in only when the IDE asks during upload.
8051, ATtiny, ATmega16/32 and LPC2148 ARM7 development boards for labs and learning pinout
The pins on the 8051, ATtiny, ATmega16/32 and LPC2148 ARM7 development boards for labs and learning and what each one does.
| Pin | Function |
|---|---|
| P0-P3 (8051) | Four 8-bit ports; P0 needs pull-ups |
| ISP header | MOSI, MISO, SCK, RESET |
| P0.14 (LPC2148) | Low at reset enters bootloader |
| P0-P5 (ATtiny85) | Six I/O pins |
| USB | Power and programming |
- P0-P3 (8051)
- Four 8-bit ports; P0 needs pull-ups
- ISP header
- MOSI, MISO, SCK, RESET
- P0.14 (LPC2148)
- Low at reset enters bootloader
- P0-P5 (ATtiny85)
- Six I/O pins
- USB
- Power and programming
Wiring the 8051, ATtiny, ATmega16/32 and LPC2148 ARM7 development boards for labs and learning
LPC2148 is a 3.3V part; do not connect 5V signals to its pins.
| 8051, ATtiny, ATmega16/32 and LPC2148 ARM7 development boards for labs and learning pin | Connection | Note |
|---|---|---|
| ISP header | USBasp programmer | Match pin 1 |
| 8051 P0 | 10k resistor network to 5V | Open-drain port |
| LPC2148 UART0 | USB-TTL at 3.3V | Flash Magic |
- ISP header
- Connection:
- USBasp programmer
- Note:
- Match pin 1
- 8051 P0
- Connection:
- 10k resistor network to 5V
- Note:
- Open-drain port
- LPC2148 UART0
- Connection:
- USB-TTL at 3.3V
- Note:
- Flash Magic
Example code
Compile with sdcc blink.c and flash the .ihx (converted to .hex) with your ISP tool.
#include <8052.h>
void delay_ms(unsigned int ms) {
unsigned int i, j;
for (i = 0; i < ms; i++)
for (j = 0; j < 120; j++); // about 1 ms at 11.0592 MHz
}
void main(void) {
while (1) {
P1_0 = 0; // LED on (sinking current)
delay_ms(500);
P1_0 = 1; // LED off
delay_ms(500);
}
}Setup and tuning
Keil or SDCC for the 8051, Microchip Studio or avr-gcc for ATmega, and Keil or GCC for ARM7.
AT89S52 and ATmega boards are flashed over ISP with a USBasp; the LPC2148 uses its serial bootloader with Flash Magic.
8051 serial code assumes 11.0592 MHz. With another crystal, baud rate timings are wrong.
5 V from USB is enough for most labs. Add an external supply when driving relays or motors.
blink an LED on a port pin first, then add the serial port, timers and interrupts.
What you need
Shop this list11 of 11 found in our store · ₹8,337
Amotech Labs 8051 Development Board w/ AT89S52 & USB-C: the part this guide coversAmotech Labs 8051 Development Board w/ AT89S52 & USB-C₹885
Amotech Labs 8051 Development Board w/ USB-C & ISP Programmer: another version this guide coversAmotech Labs 8051 Development Board w/ USB-C & ISP Programmer₹1,375
Amotech Labs 8051 Mini Development Board w/ AT89S52 MCU: another version this guide coversAmotech Labs 8051 Mini Development Board w/ AT89S52 MCU₹590
ATmega16/32 ISP AVR Minimum System Development Board: another version this guide coversATmega16/32 ISP AVR Minimum System Development Board₹309
LPC2148 ARM7 Development Module Board: another version this guide coversLPC2148 ARM7 Development Module Board₹4,265
ATTINY88 Development Board 16MHz, NANO V3.0 Compatible, Unsoldered: another version this guide coversATTINY88 Development Board 16MHz, NANO V3.0 Compatible, Unsoldered₹237
ATTINY85 USB Development Board: another version this guide coversATTINY85 USB Development Board₹227
Digispark ATTINY85 USB Microcontroller Development Board: another version this guide coversDigispark ATTINY85 USB Microcontroller Development Board₹247
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Solderless breadboard: to build without solderingSolderless Breadboard₹68
Alternatives and when to choose them
- Microchip Xplained and Curiosity Nano: modern AVR with debugger.
- Microchip PIC and AVR boards: PIC boards.
- Arduino Uno: the easiest start.
Common mistakes to avoid
- Using the wrong crystal value in serial code, so the baud rate is off.
- Connecting an ISP programmer the wrong way round on the 10-pin header.
- Driving relays or motors straight from the port pins.
- Setting AVR fuses wrongly, which can lock the chip until it is recovered.
Frequently asked questions
Can I program an 8051 board with the Arduino IDE?
Not directly. The 8051 uses Keil or SDCC; the ATmega and ATtiny boards can use the Arduino IDE with the right core.
What programmer do I need for the AT89S52?
A USBasp or similar ISP programmer with software such as ProgISP, unless the board has a built-in programmer.
Why is my 8051 serial output garbled?
The baud rate depends on the crystal. With 11.0592 MHz and the right timer reload value, 9600 baud works exactly.
Is the LPC2148 still worth learning?
It is still on many syllabuses and teaches ARM basics well, though modern projects usually use STM32 or RP2040.
What is the Digispark ATtiny85 used for?
It is a tiny USB board for simple tasks like USB keyboards or small sensors, programmed from the Arduino IDE.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
