Comparison · Intermediate · 3 min read
Bed Levelling Probes and Limit Switches
BLTouch, CR Touch, Inductive and Strain Gauge
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Auto bed levelling probes measure the bed height at several points so the printer can correct for a tilted or warped bed. BLTouch and CR Touch work on any bed material, inductive probes need a metal bed, and strain gauge sensors in the nozzle work on any surface. Set the Z offset after fitting any probe, then save a mesh.
Key specs at a glance
- BLTouch / CR Touch
- Servo-driven pin, works on any bed, 5 V power, 3-pin servo plus 2-pin signal
- Inductive probe
- Senses metal beds only, 6 to 36 V, NPN or PNP output
- Capacitive probe
- Senses most materials but is sensitive to temperature
- Strain gauge
- Built into the nozzle or bed; modern printers use it with no probe arm
- Limit switch
- Mechanical, normally open or closed; marks axis ends
- Software
- Marlin G29 or Klipper bed mesh; set the Z offset
Which probe type
Pick the probe that suits your bed and mainboard.
| Type | Works on | Pros | Cons |
|---|---|---|---|
| BLTouch / CR Touch | Any bed | Accurate, widely supported | Moving parts; needs the right mount |
| Inductive (NPN/PNP) | Metal beds | Simple and tough | Needs a level shifter for 3.3 V boards; height changes with temperature |
| Capacitive | Many materials | No moving parts | Drifts with humidity and temperature |
| Strain gauge | Any bed | Printer-integrated, no probe offset | Only comes built into some printers |
| Mechanical limit switch | Axis end | Simple and cheap | Only for homing, not mesh levelling |
- BLTouch / CR Touch
- Works on:
- Any bed
- Pros:
- Accurate, widely supported
- Cons:
- Moving parts; needs the right mount
- Inductive (NPN/PNP)
- Works on:
- Metal beds
- Pros:
- Simple and tough
- Cons:
- Needs a level shifter for 3.3 V boards; height changes with temperature
- Capacitive
- Works on:
- Many materials
- Pros:
- No moving parts
- Cons:
- Drifts with humidity and temperature
- Strain gauge
- Works on:
- Any bed
- Pros:
- Printer-integrated, no probe offset
- Cons:
- Only comes built into some printers
- Mechanical limit switch
- Works on:
- Axis end
- Pros:
- Simple and cheap
- Cons:
- Only for homing, not mesh levelling
Fitting a probe
- 1Mount the probe near the nozzle so it triggers just before the nozzle touches the bed.
- 2Wire the signal, ground and 5 V (or the supply the probe needs) to the mainboard's probe header. Inductive probes may need a divider or optocoupler for the logic level (level shifting).
- 3Enable the probe in firmware (Marlin: BLTOUCH or the matching probe option, set the probe offsets).
- 4Home all axes, then run the Z offset adjustment with a sheet of paper.
- 5Run a bed mesh (G29), save it with M500 and enable levelling at print start.
Setting the Z offset
Put the nozzle at Z = 0, lower it until a sheet of paper drags lightly, then save that value as the Z offset. Make small changes while a first layer prints: if the line is thin and not sticking, lower the nozzle; if it is flat and translucent or the nozzle scratches, raise it.
Troubleshooting
check power and the signal pin, and confirm the cable pinout.
loosen the probe mount or heat soak the bed first.
inductive probes change with temperature; re-set the offset hot.
adjust the height or replace the pin.
check the limit switch wires and the endstop type in firmware.
Try it: Stepper steps per mm calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Connecting a 24 V probe output straight to a 3.3 V input.
- Mounting the probe so loosely that it moves.
- Setting the Z offset on a cold bed and printing hot.
- Forgetting to save the settings with M500.
- Using an inductive probe on a glass bed.
Frequently asked questions
BLTouch or CR Touch?
They do the same job. CR Touch is the Creality version and is plug-and-play on many Creality printers.
Do I need auto levelling?
Not strictly, but it saves time and improves first layers on warped beds.
What is a Z offset?
The distance between the point where the probe triggers and the nozzle tip touching the bed.
Why does my mesh change between runs?
Thermal expansion, loose parts or a noisy probe. Heat soak the bed and tighten the mounts.
Are limit switches different from probes?
Yes, limit switches mark the end of an axis for homing. Probes measure the bed.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




