Component guide · Advanced · 5 min read
Acoustic Emission Sensors

QAWRUMS G10, G40, G80, G150 Resonant AE Sensors, GH150 High-Temperature, GI and GSI150 Intrinsically Safe, W500, W800 and WI500 Wideband with Preamp, and XIYUAN IEPE Piezoelectric Accelerometer
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Acoustic emission (AE) sensors listen for tiny high-frequency stress waves released when a crack grows, a weld leaks or a bearing wears. They are used in non-destructive testing of tanks, pipes and structures. Resonant sensors at 40, 80 or 150 kHz are the most sensitive at one frequency; wideband sensors capture the waveform for analysis. They need a preamplifier and a fast acquisition system, not an Arduino.
Key specs at a glance
- Frequency
- Resonant 40, 80, 150, 260 kHz; wideband up to about 500-800 kHz
- Sensitivity
- About 65 to 80 dB ref 1 V/(m/s) by model
- Temperature
- -20 to 120 C standard; up to 350 or 600 C on GH models
- Connector
- BNC, SMA or M5
- Special
- Built-in 28 V preamp on WI500; intrinsically safe GI/GSI for hazardous areas
- IEPE accelerometer
- 100 mV/g, constant-current powered, for vibration
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1QAWRUMS G10 Piezoelectric AE Sensor, >80dB, IP62, -20℃~120℃, BNC₹18,959
Option 2QAWRUMS G150/1 Piezoelectric AE Sensor, >75dB, 150 kHz, IP68, SUS-304 Stainless Steel, Ceramic Face, BNC Connector₹28,599
Option 3QAWRUMS G40 Resonant Piezoelectric AE Sensor, >75dB, 40KHz, -20℃~120℃, M5 Connector₹21,945
Option 4QAWRUMS G80 Resonant Piezoelectric AE Sensor, >75dB, 80KHz, -20℃~120℃, IP62, SUS-304 Stainless Steel, Ceramic Face, M5 Connector₹27,499
Option 5QAWRUMS G80/1 Piezoelectric AE Sensor, 80 kHz, >70dB, IP68, -20℃~120℃, BNC Connector₹29,287
Option 6QAWRUMS GH150 High Temperature AE Sensor, 260kHz, -45℃ to 600℃, BNC Connector₹3,42,179
What the Acoustic emission and IEPE piezo sensors: resonant, wideband, high-temperature and intrinsically safe AE sensors is
An acoustic emission sensor is a piezoelectric transducer that picks up the very high-frequency stress waves from cracks, leaks and wear inside metal and composite structures.
Couple the sensor to a clean, flat surface with a thin layer of couplant (grease or gel) and hold it with a magnetic holder or clamp; an air gap kills the signal. Check each sensor with a pencil lead break (Hsu-Nielsen test) next to it before trusting a test.
AE sensors give microvolt signals at hundreds of kHz, so feed them into a 40 dB preamplifier and an AE system or fast ADC sampling several MHz. The IEPE accelerometer is different: it measures lower-frequency vibration and needs a 2 to 20 mA constant-current supply, built into most vibration DAQ inputs.
Acoustic emission and IEPE piezo sensors: resonant, wideband, high-temperature and intrinsically safe AE sensors pinout
The pins on the Acoustic emission and IEPE piezo sensors: resonant, wideband, high-temperature and intrinsically safe AE sensors and what each one does.
| Pin | Function |
|---|---|
| BNC / SMA / M5 | Signal and screen |
| Preamp output | To the acquisition channel |
| 28 V phantom | Power for sensors with built-in preamp |
| IEPE | Signal and constant-current power on one coax |
- BNC / SMA / M5
- Signal and screen
- Preamp output
- To the acquisition channel
- 28 V phantom
- Power for sensors with built-in preamp
- IEPE
- Signal and constant-current power on one coax
Wiring the Acoustic emission and IEPE piezo sensors: resonant, wideband, high-temperature and intrinsically safe AE sensors
In hazardous areas only intrinsically safe sensors with a certified barrier may be used; follow the site's ATEX or equivalent rules.
| Acoustic emission and IEPE piezo sensors: resonant, wideband, high-temperature and intrinsically safe AE sensors pin | Connection | Note |
|---|---|---|
| Sensor | Preamplifier input | Short low-noise coax |
| Preamp | AE system channel | Supplies preamp power |
| IEPE sensor | IEPE input on DAQ | Enable current source |
- Sensor
- Connection:
- Preamplifier input
- Note:
- Short low-noise coax
- Preamp
- Connection:
- AE system channel
- Note:
- Supplies preamp power
- IEPE sensor
- Connection:
- IEPE input on DAQ
- Note:
- Enable current source
Example code
Exact expected amplitudes depend on the sensor, material and system; use the values from your first good check as the baseline.
1. Clean the surface and apply a thin film of couplant.
2. Clamp the sensor with steady pressure.
3. Connect sensor > preamp (40 dB) > AE channel; set threshold about 40 dB AE.
4. Break a 0.5 mm 2H pencil lead at 30 degrees, 3 cm from the sensor, 3 times.
5. Each break should give a hit of roughly 90-100 dB AE.
6. Record the amplitude for every sensor; a sensor reading well below the others
is poorly coupled or damaged.
7. Repeat the check at the end of the test.Setup and tuning
use a thin layer of couplant gel or grease between the sensor and the surface; an air gap blocks the signal.
hold the sensor with a magnetic holder, clamp or adhesive so it does not move during the test.
most sensors need a 40 dB preamplifier close to the sensor. Some models have one built in and need 28 V phantom power.
check every channel with a 0.5 mm pencil lead break near the sensor before testing.
150 kHz resonant sensors suit metal tanks and pipes; lower frequencies travel further on large structures.
What you need
Shop this list15 of 15 found in our store · ₹8,61,234
QAWRUMS G10 Piezoelectric AE Sensor, >80dB, IP62, -20℃~120℃, BNC: the part this guide coversQAWRUMS G10 Piezoelectric AE Sensor, >80dB, IP62, -20℃~120℃, BNC₹18,959
QAWRUMS G150/1 Piezoelectric AE Sensor, >75dB, 150 kHz, IP68, SUS-304 Stainless Steel, Ceramic Face, BNC Connector: another version this guide coversBNC Connector₹38
QAWRUMS G40 Resonant Piezoelectric AE Sensor, >75dB, 40KHz, -20℃~120℃, M5 Connector: another version this guide coversQAWRUMS G40 Resonant Piezoelectric AE Sensor, >75dB, 40KHz, -20℃~120℃, M5 Connector₹21,945
QAWRUMS G80 Resonant Piezoelectric AE Sensor, >75dB, 80KHz, -20℃~120℃, IP62, SUS-304 Stainless Steel, Ceramic Face, M5 Connector: another version this guide coversQAWRUMS G80 Resonant Piezoelectric AE Sensor, >75dB, 80KHz, -20℃~120℃, IP62, SUS-304 Stainless Steel, Ceramic Face, M5 Connector₹27,499
QAWRUMS G80/1 Piezoelectric AE Sensor, 80 kHz, >70dB, IP68, -20℃~120℃, BNC Connector: another version this guide coversBNC Connector₹38
QAWRUMS GH150 High Temperature AE Sensor, 260kHz, -45℃ to 600℃, BNC Connector: another version this guide coversBNC Connector₹38
QAWRUMS GH150/1 High-Temperature AE Sensor | 150 kHz, 73 dB, −20 °C to 350 °C, BNC, 3M Cable: another version this guide coversQAWRUMS GH150/1 High-Temperature AE Sensor | 150 kHz, 73 dB, −20 °C to 350 °C, BNC, 3M Cable₹2,63,209
QAWRUMS GI150 Piezoelectric AE Sensor, >75dB, 150 kHz, -20℃~50℃, BNC: another version this guide coversQAWRUMS GI150 Piezoelectric AE Sensor, >75dB, 150 kHz, -20℃~50℃, BNC₹30,259
QAWRUMS GI150/5 Intrinsically Safe AE Sensor, 150 kHz, 73dB, SMA Connector: another version this guide coversQAWRUMS GI150/5 Intrinsically Safe AE Sensor, 150 kHz, 73dB, SMA Connector₹1,84,249
QAWRUMS GI40/2 Piezoelectric AE Sensor, 40 kHz, >75dB, IP68, SUS-304 Stainless Steel, Ceramic Face, BNC Connector, 10m Cable: another version this guide coversBNC Connector₹38
QAWRUMS GSI150 Intrinsically Safe AE Sensor >73dB, 150kHz, SMA Connector: another version this guide coversQAWRUMS GSI150 Intrinsically Safe AE Sensor >73dB, 150kHz, SMA Connector₹1,83,327
QAWRUMS W500/1 Piezoelectric AE Sensor, >65dB, 500 KHz, -20℃~120℃, IP68, BNC: another version this guide coversQAWRUMS W500/1 Piezoelectric AE Sensor, >65dB, 500 KHz, -20℃~120℃, IP68, BNC₹32,479
QAWRUMS W800/1 Piezoelectric AE Sensor, >65dB, 600 KHz, -20℃~120℃, IP68, SUS-304, BNC: another version this guide coversQAWRUMS W800/1 Piezoelectric AE Sensor, >65dB, 600 KHz, -20℃~120℃, IP68, SUS-304, BNC₹41,249
QAWRUMS WI500 Wideband AE Sensor, >65dB, 500kHz, Built-In Preamplifier (28V), SMA Connector: another version this guide coversQAWRUMS WI500 Wideband AE Sensor, >65dB, 500kHz, Built-In Preamplifier (28V), SMA Connector₹37,919
XIYUAN A26D100T20 Piezoelectric Acceleration Sensor, 100mV/g @ 160Hz, IEPE Output, IP65, MIL Connector w/ 3M Cable: another version this guide coversXIYUAN A26D100T20 Piezoelectric Acceleration Sensor, 100mV/g @ 160Hz, IEPE Output, IP65, MIL Connector w/ 3M Cable₹19,989
Alternatives and when to choose them
- Piezo sensors and discs: low-cost vibration and knock.
- 40kHz ultrasonic transducers: transmit and receive in air.
Common mistakes to avoid
- Mounting the sensor dry, with no couplant.
- Running a long cable before the preamplifier, which adds noise.
- Skipping the pencil lead break check before a test.
- Using a standard sensor on a surface hotter than its rating.
Frequently asked questions
Can I read an AE sensor with an Arduino?
Not usefully. The signals are hundreds of kHz and need a preamplifier and a fast acquisition system, not a 10 kHz Arduino ADC.
What is a pencil lead break test?
Breaking a 0.5 mm pencil lead on the surface makes a standard sound pulse, used to check that each sensor responds as expected.
What is the difference between resonant and wideband sensors?
Resonant sensors are most sensitive at one frequency; wideband sensors capture a flatter range for analysing the waveform.
Can AE sensors work on hot pipes?
Standard sensors handle up to about 120 C; the high-temperature GH models are rated much higher.
Which sensors suit hazardous areas?
The intrinsically safe GI and GSI models are made for areas with flammable gas, with the right barriers.
Parts for this guide
- ₹18,959View
QAWRUMS G150/1 Piezoelectric AE Sensor, >75dB, 150 kHz, IP68, SUS-304 Stainless Steel, Ceramic Face, BNC Connector₹28,599View- ₹21,945View
QAWRUMS G80 Resonant Piezoelectric AE Sensor, >75dB, 80KHz, -20℃~120℃, IP62, SUS-304 Stainless Steel, Ceramic Face, M5 Connector₹27,499View- ₹29,287View
- ₹3,42,179View
- ₹2,63,209View
- ₹30,259View
- ₹1,84,249View
QAWRUMS GI40/2 Piezoelectric AE Sensor, 40 kHz, >75dB, IP68, SUS-304 Stainless Steel, Ceramic Face, BNC Connector, 10m Cable₹66,899View- ₹1,83,327View
- ₹32,479View
- ₹41,249View
- ₹37,919View
XIYUAN A26D100T20 Piezoelectric Acceleration Sensor, 100mV/g @ 160Hz, IEPE Output, IP65, MIL Connector w/ 3M Cable₹19,989View
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
