Component guide · Intermediate · 3 min read
Piezo Sensors and Discs
Knock Sensors, Vibration Film and Acoustic Emission Probes
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A piezo sensor creates a voltage when it is bent, knocked or vibrated. Knock modules and vibration film are easy to read with an Arduino ADC after a protection resistor and a high-value bleed resistor. Acoustic emission (AE) sensors are tuned piezo probes that need proper amplifiers. Piezo output is a spike, so sample quickly or use peak detection.
Key specs at a glance
- Knock modules
- Piezo disc with a comparator or analog output
- Vibration film
- Flexible PVDF film with a 3-pin interface
- AE probes
- Resonant 40 kHz or wide-band 150 kHz, BNC or M5 connector
- Output
- Voltage spikes, can exceed 5 V on hard hits
- Input
- High-impedance; protect with resistor and clamp
- Temperature
- -20 to 120 °C on industrial AE probes
Which sensor
Pick by the signal you need.
| Sensor | Senses | Notes |
|---|---|---|
| Knock sensor module | Taps, impacts, drum hits | Digital or analog output; simple |
| Flexible piezo film | Bending and vibration | Thin and sensitive; good for wearables |
| Bare piezo disc | Impacts, buzzing (also a sounder) | Needs your own protection circuit |
| AE sensor (G10, G40, G150) | Ultrasonic stress waves | Leak, crack, tool wear and bearing monitoring |
| Sound detection module | Loud noise only | Microphone-style; not piezo |
- Knock sensor module
- Senses:
- Taps, impacts, drum hits
- Notes:
- Digital or analog output; simple
- Flexible piezo film
- Senses:
- Bending and vibration
- Notes:
- Thin and sensitive; good for wearables
- Bare piezo disc
- Senses:
- Impacts, buzzing (also a sounder)
- Notes:
- Needs your own protection circuit
- AE sensor (G10, G40, G150)
- Senses:
- Ultrasonic stress waves
- Notes:
- Leak, crack, tool wear and bearing monitoring
- Sound detection module
- Senses:
- Loud noise only
- Notes:
- Microphone-style; not piezo
Reading a piezo with an Arduino
A piezo can generate voltages well above 5 V on a hard knock. Place a 1 MΩ resistor across the sensor to bleed charge, add a series resistor (about 1 kΩ) to the ADC pin, and clamp the input with diodes or a Zener; see Zener diodes. Sample fast with an interrupt or the ADC in free-running mode and look for the peak. See ADC basics for resolution.
Acoustic emission sensors
AE sensors listen to ultrasonic waves released by leaks, cracks, friction and arcing. Resonant probes (such as 40 kHz) are very sensitive in a narrow band; wide-band probes (150 kHz class) cover more frequencies. Couple the sensor to the surface with grease, and use a preamplifier and filter. The output feeds an oscilloscope or a data-acquisition unit rather than a basic microcontroller.
Project ideas
- Drum pads and tap triggers for MIDI.
- Knock detection on a door or machine.
- Heartbeat or breathing detection from a mattress sensor.
- Vibration monitoring of motors; see vibration and tilt sensors.
- Leak detection on pipes with AE probes.
Tips
- Mount the sensor firmly so the energy transfers well.
- Keep leads short and shielded to avoid picking up mains hum.
- Use debounce or a hold-off time after each hit.
- For high-frequency work, read the op-amp guide to build a buffer.
Try it: Adc resolution calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Feeding a raw piezo directly into an ADC pin.
- Forgetting the bleed resistor.
- Sampling too slowly and missing the peak.
- Using a microcontroller ADC for ultrasonic AE signals.
- Mounting the sensor loosely.
Frequently asked questions
Can a piezo disc be both a buzzer and a sensor?
Yes. The same disc makes sound when driven and a voltage when knocked.
Why does my reading spike above 5 V?
Piezos can generate high voltage on hard hits. Add protection.
What is an AE sensor?
A piezo probe tuned to ultrasonic stress waves from materials.
How do I read a piezo with Arduino?
Add a bleed resistor and series resistor, then read with analogRead and detect the peak.
Does piezo detect steady pressure?
No. It responds to changes, not constant force.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 21 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






