Double-clap light switch
Clap twice and the lights come on. Clap twice again to switch them off.
Shop by category
Shop all componentsGreat for small shops and workshops. The PIR sensor spots someone entering and the piezo plays a short melody. An 8-second quiet period stops it repeating while they stand in the doorway.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Passive infrared sensor that detects the body heat of moving people or animals up to about 7 m away.
Follow the colours: red is power, dark grey is ground, blue is a signal.
pir_door_chime.inoVerify & upload in Electrolark// Visitor door chime
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "pir-door-chime"
// ---- pins ----
const uint8_t PIR_PIN = 2;
const uint8_t PIEZO_PIN = 3;
// ---- latest readings ----
bool motion = false;
const int MELODY[] = {659, 523, 587, 392, 0, 392, 587, 659, 523}; // a friendly "ding-dong"
const int DUR[] = {300, 300, 300, 500, 200, 300, 300, 300, 600};
const unsigned long QUIET_MS = 8000; // do not chime again for 8 s
unsigned long lastChime = 0;
void playChime() {
for (unsigned int i = 0; i < sizeof(MELODY) / sizeof(MELODY[0]); i++) {
if (MELODY[i]) tone(PIEZO_PIN, MELODY[i], DUR[i]);
delay(DUR[i] + 30);
}
noTone(PIEZO_PIN);
}
void setup() {
Serial.begin(115200);
pinMode(PIR_PIN, INPUT);
pinMode(PIEZO_PIN, OUTPUT);
delay(30000); // PIR settles for 30 s after power-up
}
void loop() {
motion = digitalRead(PIR_PIN) == HIGH;
if (motion && millis() - lastChime > QUIET_MS) {
Serial.println(F("Visitor!"));
playChime();
lastChime = millis();
}
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Give it a minute to settle after power-up and keep it away from heaters, windows and fans.
Turn the sensitivity (Sx) pot clockwise and check the module has 5 V on VCC.
Normal for a bare piezo; mount it on a small box to resonate.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), HC-SR501 PIR Motion Detector Sensor Module, Piezo Buzzer (passive), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (pir_door_chime.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹328 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Digital inputs and sensor hold time; Generating musical notes with tone().
Ideas that reuse this build: Silent alarm version and Wireless doorbell with a button. They are listed under Take it further on this page.
Clap twice and the lights come on. Clap twice again to switch them off.
Beeps and flashes any message in Morse, or key your own by hand.
Turn a membrane keypad into a two-octave piano.
See how loud a room is as a live percentage.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.