Double-clap light switch
Clap twice and the lights come on. Clap twice again to switch them off.
Shop by category
Shop all componentsThe sketch stores the Morse code for every letter and sends your message as light and sound, with correct dot, dash and spacing timing. Hold the button to key Morse manually.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Follow the colours: red is power, dark grey is ground, blue is a signal.
morse_code_beacon.inoVerify & upload in Electrolark// Morse code beacon and key
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "morse-code-beacon"
// ---- pins ----
const uint8_t BUTTON_PIN = 2;
const uint8_t PIEZO_PIN = 3;
const uint8_t LED_RED = 4;
const char MESSAGE[] = "SOS Geekobot";
const int UNIT = 120; // ms per dot; smaller = faster
const char* CODES[26] = {".-","-...","-.-.","-..",".","..-.","--.","....","..",".---","-.-",".-..","--","-.","---",".--.","--.-",".-.","...","-","..-","...-",".--","-..-","-.--","--.."};
const int TONE_HZ = 700;
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void signal(int units) {
setRedLed(true);
tone(PIEZO_PIN, TONE_HZ);
delay(units * UNIT);
noTone(PIEZO_PIN);
setRedLed(false);
delay(UNIT);
}
void sendText(const char* text) {
for (const char* p = text; *p; p++) {
if (*p == ' ') { delay(UNIT * 6); continue; }
char ch = toupper(*p);
if (ch < 'A' || ch > 'Z') continue;
for (const char* s = CODES[ch - 'A']; *s; s++) signal(*s == '.' ? 1 : 3);
delay(UNIT * 2);
}
}
void setup() {
Serial.begin(115200);
pinMode(BUTTON_PIN, INPUT_PULLUP);
pinMode(LED_RED, OUTPUT);
pinMode(PIEZO_PIN, OUTPUT);
}
void loop() {
// hold the button to key Morse by hand; release for the automatic beacon
if (digitalRead(BUTTON_PIN) == LOW) {
setRedLed(true); tone(PIEZO_PIN, TONE_HZ);
while (digitalRead(BUTTON_PIN) == LOW) delay(5);
noTone(PIEZO_PIN); setRedLed(false);
return;
}
sendText(MESSAGE);
delay(UNIT * 14);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Normal for a bare piezo; mount it on a small box to resonate.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Tactile Push Button Switch, Piezo Buzzer (passive), Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (morse_code_beacon.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹391 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Current-limiting resistors for LEDs; Generating musical notes with tone(); Pull-ups and debouncing.
Ideas that reuse this build: Mini piano. They are listed under Take it further on this page.
Clap twice and the lights come on. Clap twice again to switch them off.
Plays a friendly ding-dong whenever someone walks into the shop or room.
Turn a membrane keypad into a two-octave piano.
See how loud a room is as a live percentage.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.