Component guide · Intermediate · 3 min read
ACS758 50A, 100A and 200A Hall Current Sensor Module

Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The ACS758 measures large currents, up to 50, 100 or 200 A, by sensing the magnetic field of a thick copper path inside the package. The output is an analog voltage centred at half the supply for zero current (bidirectional versions) that moves up or down with current. It is isolated from the high-current side, which makes it suitable for battery packs, solar systems, e-bikes and motor drivers.
Key specs at a glance
- Ranges
- +/-50 A (050B), +/-100 A (100B), +/-200 A (200B); U versions unidirectional
- Sensitivity
- 40 mV/A (050B), 20 mV/A (100B), 10 mV/A (200B) at 5 V
- Supply
- 3.3 V or 5 V depending on the chip version
- Zero output
- VCC / 2 for B (bidirectional) parts
- Isolation
- Up to 4.8 kV between current path and signal
- Bandwidth
- About 120 kHz
This part can carry many amps. Use wire thick enough for the current, put a fuse close to the battery, check that connectors are rated for the load and give drivers and motors room to cool. A short at these currents melts wires in seconds.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
What the ACS758 high-current sensor module is
Current flows through the two large terminals (IP+ and IP-), never through the signal side. Use cable and lugs rated for the current. Output = Vcc/2 + sensitivity x I, so 100B at 5 V gives 2.5 V at 0 A, 4.5 V at +100 A and 0.5 V at -100 A.
An Arduino's 10-bit ADC gives about 0.24 A steps on the 100 A version; an ADS1115 improves resolution for small currents.
ACS758 high-current sensor module pinout
The pins on the ACS758 high-current sensor module and what each one does.
| Pin | Function |
|---|---|
| IP+ / IP- | High-current path (lugs or bolts) |
| VCC | 5 V (or 3.3 V version) |
| GND | Ground |
| OUT | Analog output |
- IP+ / IP-
- High-current path (lugs or bolts)
- VCC
- 5 V (or 3.3 V version)
- GND
- Ground
- OUT
- Analog output
Wiring the ACS758 high-current sensor module
Break the load's positive (or negative) wire and pass it through IP+ and IP-. Keep high-current wiring short and away from the signal wires.
| ACS758 high-current sensor module pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5V | 5V (or 3.3 V version) |
| GND | GND | GND |
| OUT | A0 | ADS1115 A0 |
| IP+ / IP- | In series with the load | In series with the load |
- VCC
- Arduino Uno:
- 5V
- ESP32:
- 5V (or 3.3 V version)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- OUT
- Arduino Uno:
- A0
- ESP32:
- ADS1115 A0
- IP+ / IP-
- Arduino Uno:
- In series with the load
- ESP32:
- In series with the load
Example code
Change SENS for your version (0.040 for 50B, 0.010 for 200B). Measure the zero at start-up with no load.
const float SENS = 0.020; // V per A for ACS758 100B at 5 V
float zero = 2.5;
float readV() { long s = 0; for (int i = 0; i < 200; i++) s += analogRead(A0); return s / 200.0 * 5.0 / 1023.0; }
void setup() {
Serial.begin(9600);
zero = readV(); // measure with no current flowing
}
void loop() {
float amps = (readV() - zero) / SENS;
Serial.print(amps, 1); Serial.println(" A");
delay(500);
}Setup and tuning
calibrate with no current at each power-up.
use crimped lugs and the right cable size for the current.
average many samples; motor currents are noisy.
sample fast and compute RMS.
What you need
Shop this list6 of 7 found in our store · ₹1,701
ACS758 100A Hall Current Sensor Module: the part this guide coversACS758 100A Hall Current Sensor Module₹447
Allegro MicroSystems ACS758LCB-050B-PFF-T Hall Current Sensor Module – 50A Bidirectional: another version this guide coversAllegro MicroSystems ACS758LCB-050B-PFF-T Hall Current Sensor Module – 50A Bidirectional₹350- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
ADS1115 16-bit 4-channel ADC module: better analog readings, especially on ESP32ADS1115 16-Bit 4-Channel ADC Module₹199
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- ACS712 vs INA219: lower current sensors.
- Hall current sensor modules: WCS2720, ACS723 and DFRobot boards.
- SCT-013 clamp sensor: non-invasive AC clamp.
Common mistakes to avoid
- Undersized cable or loose lugs on the current path.
- Wrong sensitivity for the version.
- No zero calibration.
- Expecting fine resolution at small currents with a 10-bit ADC.
Frequently asked questions
Can it measure AC?
Yes; sample quickly and compute RMS.
Is it isolated?
Yes, the current path is isolated from the signal side.
3.3 V or 5 V?
Depends on the chip version; check the marking.
How accurate is it?
About 1 percent of full scale after zero calibration.
Can it measure a solar charger?
Yes, use the bidirectional version for charge and discharge.
Parts for this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

