Component guide · Intermediate · 4 min read
32-bit Arduino Boards

Arduino Due (SAM3X8E) and Due-compatible, Arduino Zero (SAMD21), GIGA R1 WiFi (STM32H747), MKR WiFi 1010, MKR WAN 1310 LoRa, MKR NB 1500 NB-IoT, MKR Zero and MKR Vidor 4000 FPGA
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These Arduino boards use 32-bit Arm chips for more speed and memory than the UNO. The Due is a Mega-sized board with 54 pins and two DACs. The Zero is a UNO-sized SAMD21 board. GIGA R1 WiFi is the most powerful, with a dual-core STM32H747 and Wi-Fi. MKR boards are small and battery-ready, each with one radio: Wi-Fi, LoRa, NB-IoT, or an FPGA on Vidor. All run at 3.3 V logic.
Key specs at a glance
- Due
- SAM3X8E Cortex-M3, 84 MHz, 54 I/O, 2 DACs, CAN
- Zero
- SAMD21 Cortex-M0+, 48 MHz, UNO size
- GIGA R1 WiFi
- STM32H747 dual core, 76 I/O, Wi-Fi/BLE, camera and audio connectors
- MKR boards
- SAMD21 plus Wi-Fi (1010), LoRa (WAN 1310), NB-IoT (NB 1500), SD/I2S (Zero), FPGA (Vidor)
- Logic
- 3.3 V on all
- Battery
- LiPo connector and charger on MKR boards
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Arduino Due AT91SAM3X8E ARM Cortex-M3 Dev Board w/ USB₹1,350
Option 2Arduino Due Development Board A000062₹5,279
Option 3Arduino Due Development Board without Headers₹5,189
Option 4Due AT91SAM3X8E ARM Cortex-M3 Board for Arduino₹1,309
Option 5Arduino Zero 32-bit Microcontroller Board (ARM Cortex-M0+)₹4,459
Option 6Arduino GIGA R1 WiFi Development Board₹6,739
What the 32-bit Arduino boards: Due, Zero, GIGA R1 WiFi and MKR WiFi 1010, WAN 1310, NB 1500, Zero and Vidor 4000 is
These are Arduino's 32-bit boards: the Due, Zero, GIGA R1 WiFi and the small MKR family, which add speed, memory and radios beyond the 8-bit Uno.
All these boards are 3.3 V: applying 5 V to an I/O pin can destroy the chip, so check shields and sensors before stacking them. Install the matching core: Arduino SAM for Due, SAMD for Zero and MKR, Mbed OS GIGA for GIGA.
The Due has two USB ports: use the Programming port for normal uploads. MKR boards can run from a single-cell LiPo and charge it over USB; the MKR WAN 1310 and NB 1500 need an antenna fitted before transmitting. The Vidor 4000's FPGA is mainly used through Arduino's prebuilt libraries.
32-bit Arduino boards: Due, Zero, GIGA R1 WiFi and MKR WiFi 1010, WAN 1310, NB 1500, Zero and Vidor 4000 pinout
The pins on the 32-bit Arduino boards: Due, Zero, GIGA R1 WiFi and MKR WiFi 1010, WAN 1310, NB 1500, Zero and Vidor 4000 and what each one does.
| Pin | Function |
|---|---|
| Digital and analog headers | 3.3 V I/O |
| DAC0 / DAC1 | Analog output on Due; A0 DAC on SAMD boards |
| LiPo JST | Battery on MKR |
| Antenna (u.FL) | On MKR WAN, NB, WiFi |
| Programming USB | Due upload port |
| Native USB | USB device/host |
- Digital and analog headers
- 3.3 V I/O
- DAC0 / DAC1
- Analog output on Due; A0 DAC on SAMD boards
- LiPo JST
- Battery on MKR
- Antenna (u.FL)
- On MKR WAN, NB, WiFi
- Programming USB
- Due upload port
- Native USB
- USB device/host
Wiring the 32-bit Arduino boards: Due, Zero, GIGA R1 WiFi and MKR WiFi 1010, WAN 1310, NB 1500, Zero and Vidor 4000
Many UNO shields send 5 V back on I/O lines; check before stacking them on a Due, Zero or GIGA.
| 32-bit Arduino boards: Due, Zero, GIGA R1 WiFi and MKR WiFi 1010, WAN 1310, NB 1500, Zero and Vidor 4000 pin | Connection | Note |
|---|---|---|
| USB | PC | Correct core and port |
| Sensors | 3.3 V | Level shift 5 V parts |
| MKR LiPo | JST battery socket | Single cell 3.7 V |
| Antenna | u.FL | Before transmitting |
- USB
- Connection:
- PC
- Note:
- Correct core and port
- Sensors
- Connection:
- 3.3 V
- Note:
- Level shift 5 V parts
- MKR LiPo
- Connection:
- JST battery socket
- Note:
- Single cell 3.7 V
- Antenna
- Connection:
- u.FL
- Note:
- Before transmitting
Example code
The Due DAC outputs about 0.55 V to 2.75 V, not 0 to 3.3 V; buffer it with an op-amp before driving a load.
const int N = 100;
int table[N];
void setup() {
analogWriteResolution(12); // Due DAC is 12-bit
for (int i = 0; i < N; i++)
table[i] = 2048 + 2047 * sin(2 * PI * i / N);
}
void loop() {
for (int i = 0; i < N; i++) {
analogWrite(DAC0, table[i]);
delayMicroseconds(100); // about 100 Hz
}
}Setup and tuning
all these boards run at 3.3 V. Never connect 5 V signals to their pins without a level shifter.
install the right core in Boards Manager (SAM for Due, SAMD for Zero and MKR, Mbed for GIGA).
the Due and Zero have two USB ports. Use the programming port for uploads unless the guide says otherwise.
if a MKR or Zero does not show a port, double-tap reset to enter the bootloader.
MKR boards have a LiPo connector and charger; use a protected single-cell LiPo with the right polarity.
What you need
Shop this list11 of 11 found in our store · ₹51,139
Arduino Due AT91SAM3X8E ARM Cortex-M3 Dev Board w/ USB: the part this guide coversArduino Due AT91SAM3X8E ARM Cortex-M3 Dev Board w/ USB₹1,350
Arduino Due Development Board A000062: another version this guide coversArduino Due Development Board A000062₹5,279
Arduino Due Development Board without Headers: another version this guide coversArduino Due Development Board without Headers₹5,189
Due AT91SAM3X8E ARM Cortex-M3 Board for Arduino: another version this guide coversDue AT91SAM3X8E ARM Cortex-M3 Board for Arduino₹1,309
Arduino Zero 32-bit Microcontroller Board (ARM Cortex-M0+): another version this guide coversArduino Zero 32-bit Microcontroller Board (ARM Cortex-M0+)₹4,459
Arduino GIGA R1 WiFi Development Board: another version this guide coversArduino GIGA R1 WiFi Development Board₹6,739
Arduino MKR NB 1500 NB-IoT Development Board: another version this guide coversArduino MKR NB 1500 NB-IoT Development Board₹9,269
Arduino MKR Vidor 4000 FPGA & SAMD21 Dev Board: another version this guide coversArduino MKR Vidor 4000 FPGA & SAMD21 Dev Board₹5,759
Arduino MKR WAN 1310 LoRaWAN Development Board: another version this guide coversArduino MKR WAN 1310 LoRaWAN Development Board₹4,339
Arduino MKR WiFi 1010 Development Board ABX00023: another version this guide coversArduino MKR WiFi 1010 Development Board ABX00023₹4,178
Arduino MKR Zero ABX00012 with I2S Audio & SD Card: another version this guide coversArduino MKR Zero ABX00012 with I2S Audio & SD Card₹3,269
Alternatives and when to choose them
- Arduino Mega: 5 V board with many pins.
- MKR shields and carriers: add-ons for MKR.
- Official Arduino boards compared: the full range.
Common mistakes to avoid
- Applying 5 V signals to 3.3 V pins.
- Installing the wrong board core, so the board will not compile.
- Uploading through the wrong USB port on the Due or Zero.
- Plugging in a LiPo with reversed polarity.
Frequently asked questions
Can I use 5 V sensors with the Due?
Not directly. The Due is 3.3 V and its pins are not 5 V tolerant, so use level shifters or 3.3 V sensors.
Which board should I pick for a fast Arduino project?
The GIGA R1 WiFi is the most powerful; the Due is a good Mega-sized option for many 3.3 V I/O pins.
Why does my MKR board not show up in the IDE?
Double-tap the reset button to enter the bootloader, then select the new port.
Do Uno shields fit these boards?
The Due, Zero and GIGA share the Uno or Mega layout, but 5 V-only shields may not work at 3.3 V.
Which MKR board has LoRa?
The MKR WAN 1310 has a LoRa radio; the MKR WiFi 1010 has Wi-Fi and BLE.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
