Component guide · Intermediate · 4 min read
Arduino MKR Shields and Carriers

MKR 485, ETH, GPS, ENV Rev2, Mem, RGB, Therm, Proto, Proto Large, Relay Proto and SD Proto Shields, MKR Connector Carrier and MKR IoT Carrier Rev2
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
MKR shields stack on Arduino MKR boards such as the MKR WiFi 1010, MKR WAN 1310 and MKR Zero. Each adds one function: RS485, Ethernet, GPS, environmental sensors, flash and SD memory, an RGB LED matrix or a thermocouple input. The MKR IoT Carrier adds a round display, sensors, relays and buttons in one board; the Connector Carrier adds Grove ports.
Key specs at a glance
- Logic
- 3.3V only
- MKR ENV Rev2
- HTS221-type humidity, LPS22HB pressure, light and UV sensing
- MKR GPS
- u-blox SAM-M8Q, I2C or serial
- MKR ETH
- W5500 Ethernet and microSD
- MKR 485
- RS485 and RS422, screw terminals
- MKR IoT Carrier Rev2
- Round colour display, 5 touch buttons, 2 relays, sensors, SD, LiPo holder
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Arduino MKR 485 Shield ASX00004₹3,949
Option 2Arduino MKR Connector Carrier (Grove Compatible)₹2,709
Option 3Arduino MKR ENV Shield Rev2 ASX00029₹4,139
Option 4Arduino MKR ETH Shield ASX00006₹3,329
Option 5Arduino MKR GPS Shield – u-blox SAM-M8Q Module₹4,209
Option 6Arduino MKR IoT Carrier Rev2 ABX00073₹7,049
What the Arduino MKR shields and carriers is
MKR shields stack on Arduino MKR boards and each add one function, such as RS485, Ethernet, GPS or sensors, while carriers add many parts at once.
Each shield has an Arduino library with the same name (Arduino_MKRENV, Arduino_MKRGPS, ArduinoRS485, Arduino_MKRIoTCarrier). Install it from the Library Manager and open its examples.
The relays on the MKR IoT Carrier and Relay Proto Shield are for low voltages in learning projects. MKR boards are 3.3V: 5V sensors on proto shields need level shifting.
Arduino MKR shields and carriers pinout
The pins on the Arduino MKR shields and carriers and what each one does.
| Pin | Function |
|---|---|
| MKR headers | Two 14-pin rows, 3.3V logic |
| Screw terminals | On 485, Therm and relay shields |
| Grove ports | On the Connector Carrier |
| microSD | On ETH, Mem, SD Proto and IoT Carrier |
| Battery | LiPo on the MKR board or 18650 holder on the IoT Carrier |
- MKR headers
- Two 14-pin rows, 3.3V logic
- Screw terminals
- On 485, Therm and relay shields
- Grove ports
- On the Connector Carrier
- microSD
- On ETH, Mem, SD Proto and IoT Carrier
- Battery
- LiPo on the MKR board or 18650 holder on the IoT Carrier
Wiring the Arduino MKR shields and carriers
Never apply 5V to MKR pins. The IoT Carrier relays are not for mains wiring.
| Arduino MKR shields and carriers pin | Connection | Note |
|---|---|---|
| Shield | Stack on the MKR board | Match the pin labels |
| Thermocouple | K-type into the Therm shield | Polarity matters |
| RS485 | A, B, GND terminals | Terminate long lines |
- Shield
- Connection:
- Stack on the MKR board
- Note:
- Match the pin labels
- Thermocouple
- Connection:
- K-type into the Therm shield
- Note:
- Polarity matters
- RS485
- Connection:
- A, B, GND terminals
- Note:
- Terminate long lines
Example code
The library supports Rev1 and Rev2. For the IoT Carrier, use Arduino_MKRIoTCarrier and its examples.
#include <Arduino_MKRENV.h>
void setup() {
Serial.begin(9600);
while (!Serial);
if (!ENV.begin()) { Serial.println("ENV shield not found"); while (1); }
}
void loop() {
Serial.print("Temp C: "); Serial.println(ENV.readTemperature());
Serial.print("Humidity %: "); Serial.println(ENV.readHumidity());
Serial.print("Pressure kPa: "); Serial.println(ENV.readPressure());
delay(2000);
}Setup and tuning
MKR boards and shields use 3.3 V logic. Do not connect 5 V signals to them.
check pin clashes before stacking two shields; for example ETH and Mem both use SPI with different CS pins.
install the shield's library (Arduino_MKRENV, Arduino_MKRGPS, ArduinoRS485) and run its example first.
use USB, Vin or a LiPo on the MKR board; the IoT Carrier has its own battery holder.
the IoT Carrier relays suit low-voltage loads; keep mains wiring out of the carrier.
What you need
Shop this list15 of 15 found in our store · ₹46,175
Arduino MKR 485 Shield ASX00004: the part this guide coversArduino MKR 485 Shield ASX00004₹3,949
Arduino MKR Connector Carrier (Grove Compatible): another version this guide coversArduino MKR Connector Carrier (Grove Compatible)₹2,709
Arduino MKR ENV Shield Rev2 ASX00029: another version this guide coversArduino MKR ENV Shield Rev2 ASX00029₹4,139
Arduino MKR ETH Shield ASX00006: another version this guide coversArduino MKR ETH Shield ASX00006₹3,329
Arduino MKR GPS Shield – u-blox SAM-M8Q Module: another version this guide coversArduino MKR GPS Shield – u-blox SAM-M8Q Module₹4,209
Arduino MKR IoT Carrier Rev2 ABX00073: another version this guide coversArduino MKR IoT Carrier Rev2 ABX00073₹7,049
Arduino MKR Mem Shield ASX00008: another version this guide coversArduino MKR Mem Shield ASX00008₹2,849
Arduino MKR Proto Large Shield TSX00002: another version this guide coversArduino MKR Proto Large Shield TSX00002₹1,099
Arduino MKR Proto Shield TSX00001: another version this guide coversArduino MKR Proto Shield TSX00001₹949
Arduino MKR Proto Shield TSX00002: another version this guide coversArduino MKR Proto Shield TSX00002₹849
Arduino MKR RGB Shield ASX00010: another version this guide coversArduino MKR RGB Shield ASX00010₹5,659
Arduino MKR Relay Proto Shield TSX00003: another version this guide coversArduino MKR Relay Proto Shield TSX00003₹2,019
Arduino MKR SD Proto Shield TSX00004: another version this guide coversArduino MKR SD Proto Shield TSX00004₹1,659
Arduino MKR Therm Shield ASX00012: another version this guide coversArduino MKR Therm Shield ASX00012₹5,659
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- Official Arduino boards: MKR boards.
- Arduino communication shields: Uno-size versions.
- Arduino sensor shields: Grove for Uno.
Common mistakes to avoid
- Connecting 5 V signals to MKR pins.
- Stacking shields with clashing chip-select pins.
- Wiring mains loads to the carrier's relays.
- Expecting MKR shields to fit an Uno.
Frequently asked questions
Do MKR shields work on an Arduino Uno?
No. They are made for the MKR pin layout and 3.3 V logic.
Can I stack two MKR shields?
Yes, if their pins do not clash. Check each shield's pin use, especially SPI chip selects.
What is the MKR ENV shield used for?
It adds temperature, humidity, pressure and light sensing for weather and indoor monitoring.
Does the MKR GPS shield need an antenna?
It has a small built-in antenna; a clear view of the sky still matters for a fast fix.
What does the IoT Carrier include?
A round display, touch buttons, relays, sensors, an SD slot and a battery holder in one board.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
