Component guide · Beginner · 4 min read
Arduino Nano

Pinout, Clones, CH340 Drivers and Nano Every
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
The Arduino Nano is a breadboard-friendly version of the Uno: the same ATmega328P, 5 V logic and 14 digital pins, in a 45 x 18 mm board with a mini USB port. Clones with a CH340 USB chip need a driver on some Windows versions and usually the "Old Bootloader" setting. It is the right choice when the Uno is too big to fit.
Key specs at a glance
- Microcontroller
- ATmega328P at 16 MHz (classic Nano)
- Logic level
- 5 V
- Digital I/O
- 14 (D0 to D13), 6 PWM
- Analog inputs
- 8 (A0 to A7); A6 and A7 are input only
- Flash / RAM
- 32 KB / 2 KB
- Power
- Mini USB 5 V, or 7 to 12 V on VIN
- Size
- 45 x 18 mm, fits a breadboard
- Nano Every
- ATmega4809, 48 MHz, 48 KB flash, 6 KB RAM, same footprint
What is an Arduino Nano?
The Nano packs the Arduino Uno's electronics into a small board with header pins underneath, so it plugs straight into a breadboard or a socket on your own PCB. It runs the same sketches and libraries. The differences are a mini USB (or USB-C on newer boards) connector, two extra analog inputs (A6, A7) and no space for shields.
Arduino Nano pinout
| Pin(s) | Function | Notes |
|---|---|---|
| D0 (RX), D1 (TX) | Serial | Shared with USB, keep free while uploading |
| D2, D3 | External interrupts | Buttons, encoders |
| D3, D5, D6, D9, D10, D11 | PWM | analogWrite() |
| D10 to D13 | SPI (SS, MOSI, MISO, SCK) | D13 also the onboard LED |
| A0 to A5 | Analog in / digital I/O | A4 = SDA, A5 = SCL (I2C) |
| A6, A7 | Analog input only | Cannot be used as digital pins |
| 5V | 5 V out (from USB or regulator) | Not protected: feed only regulated 5 V |
| 3V3 | 3.3 V out | Only about 50 mA from the USB chip |
| VIN | 7 to 12 V in | Onboard regulator |
| RST, GND, AREF | Reset, ground, analog reference |
- D0 (RX), D1 (TX)
- Function:
- Serial
- Notes:
- Shared with USB, keep free while uploading
- D2, D3
- Function:
- External interrupts
- Notes:
- Buttons, encoders
- D3, D5, D6, D9, D10, D11
- Function:
- PWM
- Notes:
- analogWrite()
- D10 to D13
- Function:
- SPI (SS, MOSI, MISO, SCK)
- Notes:
- D13 also the onboard LED
- A0 to A5
- Function:
- Analog in / digital I/O
- Notes:
- A4 = SDA, A5 = SCL (I2C)
- A6, A7
- Function:
- Analog input only
- Notes:
- Cannot be used as digital pins
- 5V
- Function:
- 5 V out (from USB or regulator)
- Notes:
- Not protected: feed only regulated 5 V
- 3V3
- Function:
- 3.3 V out
- Notes:
- Only about 50 mA from the USB chip
- VIN
- Function:
- 7 to 12 V in
- Notes:
- Onboard regulator
- RST, GND, AREF
- Function:
- Reset, ground, analog reference
Clone Nanos: CH340 driver and the old bootloader
Most inexpensive Nanos are clones with a CH340 USB chip instead of the FT232. They work the same once two things are right:
- 1Driver: Windows 10 and 11 usually install it automatically; if the board does not appear as a COM port, install the CH340/CH341 driver from WCH. macOS and Linux need nothing.
- 2Bootloader: in the Arduino IDE choose Tools > Processor > ATmega328P (Old Bootloader). If uploads fail with "programmer is not responding", switch to the other option.
Nano boards sold with a USB-C connector are still ATmega328P clones unless they say Nano Every or Nano ESP32.
Nano vs Nano Every vs Nano ESP32 vs Nano 33
| Board | Chip | Logic | Wireless | Choose it for |
|---|---|---|---|---|
| Nano (classic/clone) | ATmega328P | 5 V | None | Cheapest, most tutorials, 5 V modules |
| Nano Every | ATmega4809 | 5 V | None | More memory, same code, official board |
| Nano ESP32 | ESP32-S3 | 3.3 V | Wi-Fi + BLE | IoT in the Nano footprint, MicroPython |
| Nano 33 IoT / BLE | SAMD21 / nRF52840 | 3.3 V | Wi-Fi or BLE | Low-power wearables, sensors on board |
- Nano (classic/clone)
- Chip:
- ATmega328P
- Logic:
- 5 V
- Wireless:
- None
- Choose it for:
- Cheapest, most tutorials, 5 V modules
- Nano Every
- Chip:
- ATmega4809
- Logic:
- 5 V
- Wireless:
- None
- Choose it for:
- More memory, same code, official board
- Nano ESP32
- Chip:
- ESP32-S3
- Logic:
- 3.3 V
- Wireless:
- Wi-Fi + BLE
- Choose it for:
- IoT in the Nano footprint, MicroPython
- Nano 33 IoT / BLE
- Chip:
- SAMD21 / nRF52840
- Logic:
- 3.3 V
- Wireless:
- Wi-Fi or BLE
- Choose it for:
- Low-power wearables, sensors on board
Powering a Nano
Use USB for the bench. For a battery or adapter, feed 7 to 12 V into VIN; a 9 V supply is ideal. The 5V pin can also be fed with a regulated 5 V (for example from a buck converter or a USB power bank), but never with an unregulated supply. Motors and servos need their own supply with a shared ground.
Try it: ADC resolution calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Choosing the wrong bootloader option; try both before suspecting the board.
- Trying to use A6 or A7 as digital pins; they are analog inputs only.
- Plugging the Nano into a breadboard the wrong way round so both pin rows share a row of holes.
- Drawing more than about 20 mA from a pin.
- Powering 5V and VIN at the same time.
Frequently asked questions
Is the Arduino Nano the same as the Uno?
Electrically almost: same chip, same pins, same code. The Nano is smaller, fits a breadboard, has A6 and A7, and cannot take Uno shields.
Why does my Arduino Nano not show up in the Arduino IDE?
Usually a missing CH340 driver on Windows, or a charge-only USB cable. Install the driver, try another cable, and check the COM port under Tools.
Which bootloader should I pick for a Nano clone?
Most clones ship with the old bootloader, so select ATmega328P (Old Bootloader). Newer clones use the current one; try the other setting if uploading fails.
Can an Arduino Nano run on 3.7 V from a Li-ion cell?
Not reliably. At 3.7 V the 16 MHz ATmega328P is out of spec and the 5 V pins misbehave. Boost the cell to 5 V or use a 3.3 V board such as the Nano ESP32.
Does the Arduino Nano have Wi-Fi?
The classic Nano and Nano Every do not. The Nano ESP32 and Nano 33 IoT have Wi-Fi built in.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 680 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
- Arduino Nano product reference and schematic (Arduino)
- Arduino Nano Every datasheet (Arduino)
- CH340 datasheet (WCH)
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



