Component guide · Advanced · 4 min read
Arduino Portenta Carriers, Shields and Pro Modules

Portenta Max, Mid and Hat Carriers, Vision Shield LoRa and Ethernet, CAT.M1/NB IoT GNSS Shield, Pro 4G Modules, Opta Expansions D1608E, D1608S and A0602, and Nicla Sense Env
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These are Arduino Pro add-ons for industrial and IoT work. Portenta carriers break out a Portenta H7, C33 or X8 to Ethernet, CAN, mPCIe, camera and Raspberry Pi HAT connectors. Vision Shields add a camera with LoRa or Ethernet. Pro 4G modules plug into the Mid Carrier for cellular data. Opta expansions add digital or analog I/O to an Opta PLC.
Key specs at a glance
- Portenta Max Carrier
- Ethernet, CAN, RS485, LoRa, mPCIe, audio, battery
- Portenta Mid Carrier
- Breakout of every Portenta pin, Ethernet, CAN, mPCIe for Pro 4G
- Portenta Hat Carrier
- Raspberry Pi HAT header, Ethernet, CAN for X8 and H7
- Vision Shields
- Himax HM01B0 or HM0360 camera, two microphones, LoRa or Ethernet
- Pro 4G / CAT.M1 GNSS
- Cellular data plus GNSS
- Opta expansions
- D1608E/S: 16 inputs, 8 relay or SSR outputs; A0602: 6 analog in, 2 analog out
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Arduino Portenta CAT.M1/NB IoT GNSS Shield ASX00027₹7,660
Option 2Arduino Portenta Hat Carrier Industrial Pi Base ASX00049₹4,719
Option 3Arduino Portenta Max Carrier – Robotics & IoT Platform₹36,049
Option 4Arduino Portenta Mid Carrier Board – IoT Expansion ASX00055₹6,575
Option 5Arduino Portenta Vision Shield LoRa ASX00026₹5,907
Option 6Arduino Portenta Vision Shield-Ethernet AI Camera₹6,649
What the Arduino Portenta carriers and shields, Pro 4G modules, Opta expansions and Nicla Sense Env is
These Arduino Pro boards plug a Portenta module into industrial connectors such as Ethernet, CAN, RS485, mPCIe and camera ports, or add I/O to an Opta.
Start with the board you already have: a Portenta H7 with the Mid Carrier is the most flexible bench set-up. Opta expansions snap onto the side of an Opta on the DIN rail and are detected automatically by the Arduino PLC IDE.
The Nicla Sense Env is a small environmental board with temperature, humidity, gas and air quality sensors, made to plug into a Portenta, Nicla or MKR board over its ESLOV connector or header.
Arduino Portenta carriers and shields, Pro 4G modules, Opta expansions and Nicla Sense Env pinout
The pins on the Arduino Portenta carriers and shields, Pro 4G modules, Opta expansions and Nicla Sense Env and what each one does.
| Pin | Function |
|---|---|
| High-density connectors | Portenta bottom connectors on carriers |
| mPCIe slot | Pro 4G module on Mid and Max carriers |
| Ethernet | On most carriers and the Vision Shield Ethernet |
| Opta expansion port | Side connector with ribbon |
| ESLOV | I2C connector on Nicla boards |
- High-density connectors
- Portenta bottom connectors on carriers
- mPCIe slot
- Pro 4G module on Mid and Max carriers
- Ethernet
- On most carriers and the Vision Shield Ethernet
- Opta expansion port
- Side connector with ribbon
- ESLOV
- I2C connector on Nicla boards
Wiring the Arduino Portenta carriers and shields, Pro 4G modules, Opta expansions and Nicla Sense Env
Power carriers from their DC jack or USB-C with enough current for 4G modules. Field wiring on Opta expansions follows the same rules as the Opta.
| Arduino Portenta carriers and shields, Pro 4G modules, Opta expansions and Nicla Sense Env pin | Connection | Note |
|---|---|---|
| Carrier | Portenta on the high-density connectors | Press evenly |
| 4G antenna | u.FL to the module | Fit before power |
| Opta expansion | Side ribbon to the Opta | 24V supply |
- Carrier
- Connection:
- Portenta on the high-density connectors
- Note:
- Press evenly
- 4G antenna
- Connection:
- u.FL to the module
- Note:
- Fit before power
- Opta expansion
- Connection:
- Side ribbon to the Opta
- Note:
- 24V supply
Example code
Library function names follow Arduino's Opta Blueprint examples; check the latest examples for your library version.
#include "OptaBlue.h"
void setup() {
Serial.begin(115200);
OptaController.begin();
}
void loop() {
OptaController.update();
for (int i = 0; i < OptaController.getExpansionNum(); i++) {
DigitalExpansion d = OptaController.getExpansion(i);
if (d) {
d.updateDigitalInputs();
Serial.print("Exp "); Serial.print(i); Serial.print(" I1 = ");
Serial.println(d.digitalRead(0));
}
}
delay(500);
}Setup and tuning
Max Carrier for a complete IoT gateway, Mid Carrier for prototyping, Hat Carrier for Raspberry Pi HATs.
align the Portenta's high-density connectors and press evenly; bent pins are hard to fix.
use the carrier's barrel or screw input (often 6 to 36 V) for full-load use, not just USB.
fit the Pro 4G module in the Mid Carrier's mPCIe slot with both antennas and an active SIM.
run the carrier's example sketches to check each interface before writing your own code.
What you need
Shop this list13 of 13 found in our store · ₹1,37,805
Arduino Portenta CAT.M1/NB IoT GNSS Shield ASX00027: the part this guide coversArduino Portenta CAT.M1/NB IoT GNSS Shield ASX00027₹7,660
Arduino Portenta Hat Carrier Industrial Pi Base ASX00049: another version this guide coversArduino Portenta Hat Carrier Industrial Pi Base ASX00049₹4,719
Arduino Portenta Max Carrier – Robotics & IoT Platform: another version this guide coversArduino Portenta Max Carrier – Robotics & IoT Platform₹36,049
Arduino Portenta Mid Carrier Board – IoT Expansion ASX00055: another version this guide coversArduino Portenta Mid Carrier Board – IoT Expansion ASX00055₹6,575
Arduino Portenta Vision Shield LoRa ASX00026: another version this guide coversArduino Portenta Vision Shield LoRa ASX00026₹5,907
Arduino Portenta Vision Shield-Ethernet AI Camera: another version this guide coversArduino Portenta Vision Shield-Ethernet AI Camera₹6,649
Arduino Pro 4G GNSS Module Global TPX00200: another version this guide coversArduino Pro 4G GNSS Module Global TPX00200₹6,178
Arduino Pro 4G Module EMEA: another version this guide coversArduino Pro 4G Module EMEA₹3,659
Arduino Pro Opta Ext A0602 Industrial I/O Module: another version this guide coversArduino Pro Opta Ext A0602 Industrial I/O Module₹24,869
Arduino Pro Opta Ext D1608E 16-Input 8-Relay I/O Module: another version this guide coversArduino Pro Opta Ext D1608E 16-Input 8-Relay I/O Module₹15,159
Arduino Pro Opta Ext D1608S Industrial Expansion Module: another version this guide coversArduino Pro Opta Ext D1608S Industrial Expansion Module₹16,229
Arduino Nicla Sense Env Environmental Sensor Board: another version this guide coversArduino Nicla Sense Env Environmental Sensor Board₹3,989
USB-C cable: for power and programmingUSB-C Power Cable with On/Off Switch for Raspberry Pi 4₹163
Alternatives and when to choose them
- Arduino Opta and Nicla Vision: the base PLC.
- SIM7600 4G modules: other 4G options.
- Official Arduino boards: Portenta boards.
Common mistakes to avoid
- Bending the high-density connector pins when fitting the module.
- Running a loaded carrier from USB power only.
- Powering the 4G module without antennas.
- Applying 5 V logic straight to Portenta pins.
Frequently asked questions
Which Portenta works with the Hat Carrier?
The Portenta X8 and H7 work with the Hat Carrier for Raspberry Pi HATs.
Can I use the Vision Shield with the Portenta H7?
Yes. It adds a camera and microphones, with LoRa or Ethernet depending on the version.
What is the Opta expansion for?
It adds more digital or analog inputs and outputs to an Opta PLC through its side connector.
Do I need a SIM for the Pro 4G module?
Yes, an active data SIM. The module also needs its antennas connected.
Is the Portenta 5 V tolerant?
No. It is 3.3 V logic; carriers provide the level shifting for their industrial ports.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

