Component guide · Intermediate · 4 min read
Arduino Pro Mini

Pinout, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Pro Mini is a tiny ATmega328P board, the same chip as the Uno, without a USB port. Upload code with a USB to TTL adapter wired to its 6-pin FTDI header, using the DTR pin for auto reset. It comes as 5 V/16 MHz or 3.3 V/8 MHz; pick the matching board option in the IDE or the sketch runs at the wrong speed.
Key specs at a glance
- Chip
- ATmega328P, 32 KB flash, 2 KB RAM
- Versions
- 5 V at 16 MHz, or 3.3 V at 8 MHz
- I/O
- 14 digital (6 PWM), 8 analog inputs (A6, A7 analog only)
- Power
- RAW 5 to 12 V into regulator, or regulated VCC
- Programming
- 6-pin header: GND, CTS, VCC, RX, TX, DTR
- Size
- 33 x 18 mm
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Pro Mini ATmega328P 5V/16MHz Development Board₹482
Option 2Arduino Pro Mini ATmega328P 3.3V 8MHz₹198
Option 3Arduino Pro Mini 328 – 3.3V / 8MHz₹1,839
What the Arduino Pro Mini is
The Pro Mini was designed to be built into finished projects: it has no USB chip, so it is smaller and cheaper and can sleep at very low current once the power LED and regulator are removed.
Code runs exactly like an Uno. You only need the USB to TTL adapter while programming.
Arduino Pro Mini pinout
The pins on the Arduino Pro Mini and what each one does.
| Pin | Function |
|---|---|
| RAW | Unregulated input to the on-board regulator |
| VCC | Regulated 5 V or 3.3 V (in or out) |
| GND | Ground |
| TXO / RXI | Serial, to adapter RX / TX |
| DTR (GRN) | Auto reset from the adapter for uploads |
| D2 to D13 | Digital I/O (D3, 5, 6, 9, 10, 11 PWM) |
| A0 to A7 | Analog inputs (A4 SDA, A5 SCL) |
| RST | Reset |
- RAW
- Unregulated input to the on-board regulator
- VCC
- Regulated 5 V or 3.3 V (in or out)
- GND
- Ground
- TXO / RXI
- Serial, to adapter RX / TX
- DTR (GRN)
- Auto reset from the adapter for uploads
- D2 to D13
- Digital I/O (D3, 5, 6, 9, 10, 11 PWM)
- A0 to A7
- Analog inputs (A4 SDA, A5 SCL)
- RST
- Reset
Wiring the Arduino Pro Mini
Set the USB to TTL adapter jumper to the same voltage as your Pro Mini (5 V or 3.3 V). If your adapter has no DTR pin, press the reset button just as the IDE starts uploading.
| Arduino Pro Mini pin | USB-TTL adapter | Notes |
|---|---|---|
| GND | GND | Common ground |
| VCC | VCC | Set the adapter jumper to the same voltage (5 V or 3.3 V) |
| RXI | TX | Crossed: adapter TX to board RX |
| TXO | RX | Crossed: board TX to adapter RX |
| DTR (GRN) | DTR | Auto reset for uploads |
- GND
- USB-TTL adapter:
- GND
- Notes:
- Common ground
- VCC
- USB-TTL adapter:
- VCC
- Notes:
- Set the adapter jumper to the same voltage (5 V or 3.3 V)
- RXI
- USB-TTL adapter:
- TX
- Notes:
- Crossed: adapter TX to board RX
- TXO
- USB-TTL adapter:
- RX
- Notes:
- Crossed: board TX to adapter RX
- DTR (GRN)
- USB-TTL adapter:
- DTR
- Notes:
- Auto reset for uploads
Example code
In the IDE choose 'Arduino Pro or Pro Mini' and then the processor option ATmega328P (5V, 16 MHz) or (3.3V, 8 MHz).
#include <LowPower.h> // Rocket Scream LowPower library
void setup() { pinMode(13, OUTPUT); }
void loop() {
digitalWrite(13, HIGH); delay(50);
digitalWrite(13, LOW);
LowPower.powerDown(SLEEP_8S, ADC_OFF, BOD_OFF); // ~8 s at a few µA (chip only)
}Setup and tuning
remove the power LED and, if powering VCC directly from a battery, the regulator; sleep current can then drop to a few µA.
works directly with 3.3 V sensors and radios such as the NRF24L01.
5 to 12 V; keep it low because the tiny regulator heats up.
are analog-only and cannot be used as digital pins.
What you need
Shop this list6 of 6 found in our store · ₹2,262
Pro Mini ATmega328P 5V/16MHz board: 5 V versionCrystal Oscillator HC-49 (Pack of 5)₹36
Pro Mini ATmega328P 5V/16MHz board: 5 V alternativeCrystal Oscillator HC-49 (Pack of 5)₹36
Arduino Pro Mini ATmega328P 3.3V 8MHz: 3.3 V version for battery and radio buildsArduino Pro Mini ATmega328P 3.3V 8MHz₹198
Arduino Pro Mini 328 3.3V/8MHz: 3.3 V alternativeArduino Pro Mini 328 – 3.3V / 8MHz₹1,839
USB to TTL serial converter: to program or talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
Solderless breadboard: to build without solderingSolderless Breadboard₹68
Alternatives and when to choose them
- Arduino Nano: same chip with USB, easier for learning.
- Pro Micro: ATmega32U4 with native USB, can act as a keyboard.
- Seeed XIAO: tiny boards with USB-C and faster chips.
Try it: Battery life calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Selecting 5 V/16 MHz in the IDE for a 3.3 V/8 MHz board, so timing and serial are wrong.
- Swapping TX and RX straight through instead of crossing them.
- Feeding 5 V from the adapter into a 3.3 V Pro Mini.
- Trying to use A6 or A7 as digital pins.
Frequently asked questions
How do I upload code to a Pro Mini?
Use a USB to TTL adapter on the 6-pin header with DTR connected, and select 'Arduino Pro or Pro Mini' with the correct voltage and speed.
5 V or 3.3 V version?
5 V for Uno-compatible shields and modules, 3.3 V for battery projects and 3.3 V sensors and radios.
Can I power it from a LiPo?
The 3.3 V/8 MHz version can run from a single LiPo connected to VCC, accepting a little drop as it discharges.
Why does upload fail?
Wrong board option, TX/RX not crossed, or no DTR. Try pressing reset at the start of upload.
How low can sleep current go?
A few µA for the chip after removing the LED and regulator.
Does it have USB?
No. That is the point: you add USB only when programming.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
