Component guide · Beginner · 4 min read
Arduino Proto Shields, Screw Terminal Shields and Cases

Mega Proto Shield Rev3, Proto Shields with Mini Breadboard, Screw Shield V2 and XD-216, Uno Proto Screw Shield, Terminal Shields, Mega GPIO Terminal Board, Uno Breakout Carrier and ABS Cases
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Proto shields give you a blank area, often with a mini breadboard, to build your own circuit on top of an Arduino. Screw terminal shields bring every pin to a screw terminal, so wires stay put in permanent installs. The Uno Breakout Carrier and Mega terminal board do the same with a base plate. ABS cases protect a finished board from dust and short circuits.
Key specs at a glance
- Proto area
- Plated holes, power and ground rails
- Mini breadboard
- 170 points on many proto shields
- Screw terminals
- All digital, analog and power pins
- Extras
- Reset button, LED, ICSP pass-through
- Sizes
- Uno, Mega 2560, GIGA
- Cases
- ABS with cut-outs for USB and power
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Arduino Mega Proto Shield Rev3₹759
Option 2Arduino Mega Prototype Shield V3.0 w/ Mini Breadboard₹118
Option 3Keyestudio MEGA Protoshield V3 for Arduino + Breadboard₹329
Option 4Keyestudio Proto Shield for Arduino w/ Mini Breadboard₹239
Option 5UNO Proto Shield with SYB-170 Mini Breadboard₹82
Option 6Screw Shield V2 Terminal Expansion Board for Arduino₹134
What the Arduino proto shields, screw terminal shields and cases is
Proto shields give you a blank soldering area on top of an Arduino, and screw terminal shields bring every pin to a screw clamp for wiring that stays put.
Use a proto shield to turn a breadboard prototype into a solid build: solder the parts onto the shield and keep the Arduino reusable. Screw shields are best for wires that go to switches, relays or sensors away from the board.
Some screw shields come unsoldered: solder the stacking headers straight, with the shield plugged into a board so the pins line up.
Arduino proto shields, screw terminal shields and cases pinout
The pins on the Arduino proto shields, screw terminal shields and cases and what each one does.
| Pin | Function |
|---|---|
| Uno R3 headers | D0-D13, A0-A5, power pins and the IOREF pin |
| ICSP header | SPI on 6 pins, used by many shields |
| IOREF | Tells the shield whether the board is 5V or 3.3V |
| Stacking headers | Let another shield sit on top |
| Reset button | Repeated on top of most shields |
- Uno R3 headers
- D0-D13, A0-A5, power pins and the IOREF pin
- ICSP header
- SPI on 6 pins, used by many shields
- IOREF
- Tells the shield whether the board is 5V or 3.3V
- Stacking headers
- Let another shield sit on top
- Reset button
- Repeated on top of most shields
Wiring the Arduino proto shields, screw terminal shields and cases
Do not over-tighten screw terminals on thin wire. Check the case has room for any stacked shields.
| Arduino proto shields, screw terminal shields and cases pin | Connection | Note |
|---|---|---|
| Field wire | Screw terminal of the pin | Ferrules for stranded wire |
| Proto circuit | Solder to the plated holes | Use the power rails |
| Case | Board on standoffs inside | Leave space for shields |
- Field wire
- Connection:
- Screw terminal of the pin
- Note:
- Ferrules for stranded wire
- Proto circuit
- Connection:
- Solder to the plated holes
- Note:
- Use the power rails
- Case
- Connection:
- Board on standoffs inside
- Note:
- Leave space for shields
Example code
Screw shields change nothing in software. Use INPUT_PULLUP for switches on long wires.
void setup() {
pinMode(2, INPUT_PULLUP); // switch between D2 terminal and GND terminal
pinMode(LED_BUILTIN, OUTPUT);
}
void loop() {
digitalWrite(LED_BUILTIN, digitalRead(2) == LOW);
}Setup and tuning
sketch the circuit on paper and keep power and ground on the rails.
test the circuit on the mini breadboard, then solder it on the proto area.
strip about 5 mm, use ferrules on stranded wire and tighten firmly.
solder the stacking headers straight, so the shield fits the board and others above it.
match the case to your board so the USB and power jacks line up.
What you need
Shop this list15 of 16 found in our store · ₹9,985
Arduino Mega Proto Shield Rev3: the part this guide coversArduino Mega Proto Shield Rev3₹759
Arduino Mega Prototype Shield V3.0 w/ Mini Breadboard: another version this guide coversArduino Mega Prototype Shield V3.0 w/ Mini Breadboard₹118
Keyestudio MEGA Protoshield V3 for Arduino + Breadboard: another version this guide coversKeyestudio MEGA Protoshield V3 for Arduino + Breadboard₹329
Keyestudio Proto Shield for Arduino w/ Mini Breadboard: another version this guide coversKeyestudio Proto Shield for Arduino w/ Mini Breadboard₹239
UNO Proto Shield with SYB-170 Mini Breadboard: another version this guide coversUNO Proto Shield with SYB-170 Mini Breadboard₹82
Screw Shield V2 Terminal Expansion Board for Arduino: another version this guide coversScrew Shield V2 Terminal Expansion Board for Arduino₹134
XD-216 Screw Shield V1 Expansion Board for Arduino: another version this guide coversXD-216 Screw Shield V1 Expansion Board for Arduino₹309
Arduino Uno Proto Screw Shield: another version this guide coversArduino Uno Proto Screw Shield₹259
Arduino UNO R3 / MEGA2560 Terminal Shield – Unsoldered: another version this guide coversArduino UNO R3 / MEGA2560 Terminal Shield – Unsoldered₹299
Arduino MEGA 2560 GPIO Terminal Board w/ Acrylic Base: another version this guide coversArduino MEGA 2560 GPIO Terminal Board w/ Acrylic Base₹1,699
Arduino Uno Breakout Carrier – ASX00085: another version this guide coversArduino Uno Breakout Carrier – ASX00085₹1,049
Black ABS Case for Arduino Mega2560 R3 with Switch: another version this guide coversBlack ABS Case for Arduino Mega2560 R3 with Switch₹239
Transparent White ABS Case for Arduino R3 Board: another version this guide coversTransparent White ABS Case for Arduino R3 Board₹122
KKSB Cases Arduino Giga Display Shield Case w/ Stand: another version this guide coversKKSB Cases Arduino Giga Display Shield Case w/ Stand₹4,299- Uno R3 development board: the controller used in the wiring tableFind this part
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- Sensor shields: plug-in sensors.
- Arduino shields guide: shield basics.
- Official Arduino boards: which board to use.
Common mistakes to avoid
- Soldering parts tall enough to block the next shield.
- Using bare stranded wire in screw terminals, which frays.
- Soldering stacking headers crooked, so the shield will not seat.
- Using an Uno-size terminal shield on a Mega and missing pins.
Frequently asked questions
What is a proto shield used for?
It lets you build a permanent circuit on top of an Arduino without designing a custom PCB.
Do screw terminal shields fit the Mega?
Use the Mega version. An Uno-size terminal shield only covers the Uno header pins.
Can I stack another shield on a proto shield?
Yes, if it has stacking headers and the parts you solder are low enough.
Why use ferrules on screw terminals?
Ferrules stop fine strands from fraying, so the clamp holds the wire firmly and safely.
Will the proto shield fit an UNO R4?
Yes. The UNO R4 keeps the Uno header layout, so Uno shields fit.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

