Component guide · Beginner · 4 min read
Brushed and Bidirectional ESCs

Hobbywing QuicRun 1060, 1625, WP 1080 and Crawler, 30A Brushed ESCs, 20A to 50A Bidirectional ESCs and BLDC Driver Boards
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These speed controllers run motors forward and backward. Brushed ESCs (Hobbywing QuicRun, 30A brushed) drive the DC motors in RC cars, boats, crawlers and robots. Bidirectional brushless ESCs drive thrusters on underwater ROVs and boats, where the propeller must spin both ways. The H-bridge board and BLDC driver board are simple drivers for small DC and brushless motors.
Key specs at a glance
- Motor type
- Brushed DC or brushless (bidirectional)
- Current
- 20A to 80A
- Voltage
- 2S to 6S LiPo or NiMH (check each)
- Signal
- 1000 to 2000 us PWM, 1500 us = stop
- Waterproof
- QuicRun WP and 1625
- BEC
- Built-in on most for receiver and steering servo
This part can carry many amps. Use wire thick enough for the current, put a fuse close to the battery, check that connectors are rated for the load and give drivers and motors room to cool. A short at these currents melts wires in seconds.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Hobbywing QuicRun 1060 60A Brushed ESC for 1/10 RC Cars₹2,959
Option 2Hobbywing QuicRun 1625 25A Waterproof Brushed ESC₹2,099
Option 3Hobbywing QuicRun WP 1080 G2 Brushed ESC 80A 2-3S₹5,169
Option 4Hobbywing Quicrun WP Crawler Brushed 80A ESC₹4,499
Option 530A Brushed ESC with Brake for RC Motors 4-8V₹429
Option 630A Brushed ESC with No Brake₹689
What the Brushed and bidirectional ESCs for RC cars, boats and robots is
These ESCs control motor speed and direction from a standard RC signal: brushed ones for RC cars, boats and robots, bidirectional brushless ones for ROV and boat thrusters.
Bidirectional ESCs stop at 1500 us, go forward above it and reverse below it. RC car ESCs also have a brake and may need a double tap of reverse to go backwards; set them to forward/reverse mode for robots.
Check the motor turn limit for brushed ESCs (for example 12T or higher on the QuicRun 1060).
Brushed and bidirectional ESCs for RC cars, boats and robots pinout
The pins on the Brushed and bidirectional ESCs for RC cars, boats and robots and what each one does.
| Pin | Function |
|---|---|
| Battery leads | Battery + and - |
| Motor leads | Two wires (brushed) or three (brushless) |
| Signal cable | PWM signal, GND and BEC 5V/6V |
| Mode jumper / switch | LiPo / NiMH and forward-brake-reverse settings |
- Battery leads
- Battery + and -
- Motor leads
- Two wires (brushed) or three (brushless)
- Signal cable
- PWM signal, GND and BEC 5V/6V
- Mode jumper / switch
- LiPo / NiMH and forward-brake-reverse settings
Wiring the Brushed and bidirectional ESCs for RC cars, boats and robots
Set the LiPo/NiMH jumper correctly so the low-voltage cut-off protects the battery. Keep waterproof ESC plugs sealed with dielectric grease in boats.
| Brushed and bidirectional ESCs for RC cars, boats and robots pin | Connection | Note |
|---|---|---|
| Battery | Battery + and - | Set LiPo mode |
| Motor | Two wires; swap to reverse | Three for brushless |
| Signal | Receiver throttle or Arduino pin | Common GND |
- Battery
- Connection:
- Battery + and -
- Note:
- Set LiPo mode
- Motor
- Connection:
- Two wires; swap to reverse
- Note:
- Three for brushless
- Signal
- Connection:
- Receiver throttle or Arduino pin
- Note:
- Common GND
Example code
Some car ESCs need neutral, then reverse, then neutral, then reverse again to engage reverse. Switch them to forward/reverse (no brake) mode for robots.
#include <Servo.h>
Servo esc;
void setup() {
esc.attach(9, 1000, 2000);
esc.writeMicroseconds(1500); // neutral to arm
delay(3000);
}
void loop() {
esc.writeMicroseconds(1600); // forward, slow
delay(2000);
esc.writeMicroseconds(1500); // stop
delay(1000);
esc.writeMicroseconds(1400); // reverse, slow
delay(2000);
esc.writeMicroseconds(1500);
delay(1000);
}Setup and tuning
send 1000 to 2000 µs pulses with 1500 µs for stop; use the Servo library on Arduino.
send the neutral signal (1500 µs) at power-up until the ESC beeps ready.
set LiPo or NiMH mode so the low-voltage cutoff is right.
use only one BEC to power the receiver; with two ESCs, remove the red wire from one.
only WP models are waterproof; keep others dry.
What you need
Shop this list12 of 14 found in our store · ₹22,356
Hobbywing QuicRun 1060 60A Brushed ESC for 1/10 RC Cars: the part this guide coversHobbywing QuicRun 1060 60A Brushed ESC for 1/10 RC Cars₹2,959
Hobbywing QuicRun 1625 25A Waterproof Brushed ESC: another version this guide coversHobbywing QuicRun 1625 25A Waterproof Brushed ESC₹2,099
Hobbywing QuicRun WP 1080 G2 Brushed ESC 80A 2-3S: another version this guide coversHobbywing QuicRun WP 1080 G2 Brushed ESC 80A 2-3S₹5,169
Hobbywing Quicrun WP Crawler Brushed 80A ESC: another version this guide coversHobbywing Quicrun WP Crawler Brushed 80A ESC₹4,499
30A Brushed ESC with Brake for RC Motors 4-8V: another version this guide covers30A Brushed ESC with Brake for RC Motors 4-8V₹429
30A Brushed ESC with No Brake: another version this guide covers30A Brushed ESC with No Brake₹689
20A Bidirectional Digital ESC: another version this guide covers20A Bidirectional Digital ESC₹829
Bidirectional 30A 2-4S UBEC 2A 5V ESC: another version this guide coversBidirectional 30A 2-4S UBEC 2A 5V ESC₹854
Bidirectional 50A 2-6S UBEC ESC: another version this guide coversBidirectional 50A 2-6S UBEC ESC₹1,419
170W H-Bridge DC Motor Driver Module, NMOS Brake, 5-30V: another version this guide covers170W H-Bridge DC Motor Driver Module, NMOS Brake, 5-30V₹1,079
5V-12V DC Brushless Motor Driver Board for 3/4 Wire Motors: another version this guide covers5V-12V DC Brushless Motor Driver Board for 3/4 Wire Motors₹939- Uno R3 development board: the controller used in the wiring tableFind this part
- Servo tester: spins a motor through the ESC without a receiverFind this part
2S 7.4V LiPo battery pack (XT60): for bench tests and small modelsBonka 2S 7.4V LiPo Battery Pack (1000 to 4200mAh, XT60)₹1,392Closest match, check the specs
Alternatives and when to choose them
- BTS7960 driver: Arduino H-bridge.
- Cytron MD10C: PWM DC driver.
- Multirotor ESCs: one direction only.
Common mistakes to avoid
- Powering the receiver from two BECs at once.
- Not sending neutral at power-up, so the ESC never arms.
- Using a non-waterproof ESC in a boat hull that gets wet.
- Leaving the cutoff on NiMH mode with a LiPo battery.
Frequently asked questions
Can I control a brushed ESC with an Arduino?
Yes. Use the Servo library: 1500 µs is stop, higher is forward and lower is reverse.
Why does my ESC not start?
It needs the neutral signal at power-up to arm. Send 1500 µs for a few seconds first.
What is a bidirectional ESC for?
It spins a brushless motor both ways, which ROV and boat thrusters need for reverse.
Can I use a car ESC on a drone?
No. Car ESCs are too slow for flight control; drones need dedicated ESCs.
Why is there a delay when reversing?
Many car ESCs need neutral, brake, then reverse. Change the mode in the ESC settings.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


