Component guide · Intermediate · 5 min read
Global Shutter CSI Cameras

IMX296 (Arducam, Waveshare), OV9281 Mono, AR0234 Full HD, OV9782 and ISG1321 for Pi and Jetson
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A global shutter camera captures the whole frame at the same instant, so fast-moving objects, spinning parts and robot motion come out without the slanted rolling-shutter blur. The IMX296 (1.6MP) is the sensor in the official Pi global shutter camera; the OV9281 is a 1MP mono sensor popular for tracking; the AR0234 gives colour full HD at high frame rates. Most suit machine vision and robotics.
Key specs at a glance
- Sensors
- IMX296 1.6MP, OV9281 1MP mono, AR0234 2.3MP, OV9782 1MP colour, ISG1321 1.38MP
- Frame rate
- 60 to 120 fps or more
- Interface
- MIPI CSI-2
- Colour
- Mono (OV9281, ISG1321) or colour
- Trigger
- External trigger on several boards
- Lens
- M12 or CS mount
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Arducam 1.58MP IMX296 Global Shutter Camera Module w/ M12 Lens for Raspberry Pi₹7,099
Option 2Waveshare IMX296 1.6MP Global Shutter Mono Camera Module for Raspberry Pi₹7,209
Option 3Waveshare IMX296 Global Shutter Camera Module (A) for Raspberry Pi₹7,159
Option 4Arducam OV9281 1MP Global Shutter Monochrome NoIR Camera Module w/ M12 Lens₹5,769
Option 5Waveshare OV9281-110 Mono 1MP Global Shutter Camera for Raspberry Pi₹3,009
Option 6Waveshare OV9281-120 Mono Camera Module, Global Shutter, 1MP₹3,319
What the Global shutter CSI cameras (IMX296, OV9281, AR0234) is
Global shutter CSI cameras capture every pixel at the same instant, so fast-moving objects are not skewed, for robotics and machine vision on Raspberry Pi and Jetson.
Global shutters suit barcode reading, measuring moving parts, visual odometry and AprilTag tracking. Mono sensors are more sensitive and many are NoIR, so they work with IR lighting.
The Pi supports IMX296 and OV9281 with built-in overlays; AR0234 boards need Arducam or Jetson drivers.
Global shutter CSI cameras (IMX296, OV9281, AR0234) pinout
The pins on the Global shutter CSI cameras (IMX296, OV9281, AR0234) and what each one does.
| Pin | Function |
|---|---|
| CSI ribbon (15 or 22-pin) | Camera data lanes, clock, I2C control and power in one flat cable |
| Metal contacts | Face the connector contacts; a reversed cable gives 'no cameras available' |
| Lens mount | Fixed, M12 or CS/C mount depending on the board |
| IR-CUT / focus motor | Driven over the same ribbon on boards that have them |
- CSI ribbon (15 or 22-pin)
- Camera data lanes, clock, I2C control and power in one flat cable
- Metal contacts
- Face the connector contacts; a reversed cable gives 'no cameras available'
- Lens mount
- Fixed, M12 or CS/C mount depending on the board
- IR-CUT / focus motor
- Driven over the same ribbon on boards that have them
Wiring the Global shutter CSI cameras (IMX296, OV9281, AR0234)
Turn the Pi off before connecting. Lift the connector latch, push the ribbon fully in with the contacts facing the pins, then press the latch down. The Pi 5 and Zero use the smaller 22-pin connector. Jetson boards use their own CSI connector and drivers.
| Global shutter CSI cameras (IMX296, OV9281, AR0234) pin | Raspberry Pi 5 | Raspberry Pi 4 |
|---|---|---|
| Ribbon cable | CAM/DISP 0 or 1 (22-pin, use a 15-to-22 cable) | CAMERA port (15-pin) |
| Power | From the ribbon (no extra wires) | From the ribbon (no extra wires) |
| Software | rpicam-apps / Picamera2 (Bookworm) | rpicam-apps / Picamera2 (Bookworm) |
- Ribbon cable
- Raspberry Pi 5:
- CAM/DISP 0 or 1 (22-pin, use a 15-to-22 cable)
- Raspberry Pi 4:
- CAMERA port (15-pin)
- Power
- Raspberry Pi 5:
- From the ribbon (no extra wires)
- Raspberry Pi 4:
- From the ribbon (no extra wires)
- Software
- Raspberry Pi 5:
- rpicam-apps / Picamera2 (Bookworm)
- Raspberry Pi 4:
- rpicam-apps / Picamera2 (Bookworm)
Example code
Check the camera first with rpicam-hello --list-cameras. Third-party sensors usually need camera_auto_detect=0 and the right dtoverlay= line in /boot/firmware/config.txt, or the maker's driver package. Overlays: dtoverlay=imx296 or dtoverlay=ov9281.
from picamera2 import Picamera2
from picamera2.encoders import H264Encoder
import time
cam = Picamera2()
cam.configure(cam.create_still_configuration())
cam.start()
time.sleep(2) # let exposure and white balance settle
cam.capture_file("gs.jpg")
cam.stop()
video = cam.create_video_configuration(main={"size": (1920, 1080)})
cam.configure(video)
cam.start_recording(H264Encoder(10_000_000), "clip.h264")
time.sleep(10)
cam.stop_recording()Setup and tuning
enable the right overlay (for example dtoverlay=imx296 on Raspberry Pi) or install the maker's driver.
fit the lens and set focus and aperture for your working distance.
use short exposures and enough light to freeze motion.
wire the trigger input to sync capture with a strobe or another camera.
choose mono sensors for low light and edge detection, colour for colour sorting.
What you need
Shop this list17 of 18 found in our store · ₹1,88,774
Arducam 1.58MP IMX296 Global Shutter Camera Module w/ M12 Lens for Raspberry Pi: the part this guide coversArducam 1.58MP IMX296 Global Shutter Camera Module w/ M12 Lens for Raspberry Pi₹7,099
Waveshare IMX296 1.6MP Global Shutter Mono Camera Module for Raspberry Pi: another version this guide coversWaveshare IMX296 1.6MP Global Shutter Mono Camera Module for Raspberry Pi₹7,209
Waveshare IMX296 Global Shutter Camera Module (A) for Raspberry Pi: another version this guide coversWaveshare IMX296 Global Shutter Camera Module (A) for Raspberry Pi₹7,159
Arducam OV9281 1MP Global Shutter Monochrome NoIR Camera Module w/ M12 Lens: another version this guide coversArducam OV9281 1MP Global Shutter Monochrome NoIR Camera Module w/ M12 Lens₹5,769
Waveshare OV9281-110 Mono 1MP Global Shutter Camera for Raspberry Pi: another version this guide coversWaveshare OV9281-110 Mono 1MP Global Shutter Camera for Raspberry Pi₹3,009
Waveshare OV9281-120 Mono Camera Module, Global Shutter, 1MP: another version this guide coversWaveshare OV9281-120 Mono Camera Module, Global Shutter, 1MP₹3,319
Waveshare OV9281-160 1MP Mono Camera w/ Global Shutter for Raspberry Pi: another version this guide coversWaveshare OV9281-160 1MP Mono Camera w/ Global Shutter for Raspberry Pi₹2,855
Arducam B0223 OV9281 1MP Global Shutter NoIR Camera Module for Jetson Orin: another version this guide coversArducam B0223 OV9281 1MP Global Shutter NoIR Camera Module for Jetson Orin₹5,699
Arducam B0224 OV9281 1MP Global Shutter NoIR Mono Camera w/ M12 Mount: another version this guide coversArducam B0224 OV9281 1MP Global Shutter NoIR Mono Camera w/ M12 Mount₹4,679
Arducam B0353 Full HD Color Global Shutter Camera for Raspberry Pi, 2.3MP AR0234: another version this guide coversArducam B0353 Full HD Color Global Shutter Camera for Raspberry Pi, 2.3MP AR0234₹12,869
Arducam 2.3MP AR0234 Global Shutter Camera for Jetson Nano/Xavier NX/Orin NX: another version this guide coversArducam 2.3MP AR0234 Global Shutter Camera for Jetson Nano/Xavier NX/Orin NX₹12,655
Arducam 2.3MP Global Shutter Camera Module for Jetson Orin Nano/NX: another version this guide coversArducam 2.3MP Global Shutter Camera Module for Jetson Orin Nano/NX₹16,605
Arducam B0335 1MP OV9782 Global Shutter MIPI Camera for OAK-D M1090FFC: another version this guide coversArducam B0335 1MP OV9782 Global Shutter MIPI Camera for OAK-D M1090FFC₹6,029
Waveshare ISG1321 1.38MP Mono Camera Module w/ Global Shutter: another version this guide coversWaveshare ISG1321 1.38MP Mono Camera Module w/ Global Shutter₹2,699
Raspberry Pi 5 (4 GB): the computer the camera plugs intoRaspberry Pi 5 16GB RAM Single Board Computer₹36,169Closest match, check the specs
NVIDIA Jetson Orin Nano Super developer kit: for AI vision with CSI camerasNVIDIA Jetson Orin Nano Super Developer Kit₹54,724
15-pin to 22-pin camera cable: for Raspberry Pi 5 and Zero boardsArducam CB008 3.8cm 15-Pin to 22-Pin Camera Cable for Raspberry Pi Zero/W₹227- Camera ribbon extension cable set: to mount the camera away from the boardFind this part
Alternatives and when to choose them
- Starlight cameras: low light, rolling shutter.
- USB global shutter: no CSI port needed.
- Depth cameras: stereo depth.
Common mistakes to avoid
- Expecting a rolling-shutter driver to work with a global shutter sensor.
- Using long exposures that blur motion anyway.
- Sending a 5 V trigger to a 3.3 V input.
- Fitting the ribbon cable reversed.
Frequently asked questions
What is the advantage of a global shutter?
All pixels expose together, so fast motion is not bent or skewed.
Which camera works on Raspberry Pi 5?
The Raspberry Pi Global Shutter Camera (IMX296) and supported Arducam models work with the right cable.
Why are my images dark?
Short exposures need more light; add lighting or increase gain.
Can I trigger the camera from an Arduino?
Yes, on models with a trigger input, using a level-matched pulse.
Is a mono camera better for vision?
Mono sensors are more sensitive and sharper for edge and pattern work.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


