Component guide · Intermediate · 3 min read
Cytron SmartDrive MDDS30, MDDS10 and MDDS60

RC, Serial and Analog Control
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Cytron SmartDrive boards are high-current brushed DC motor drivers with a microcontroller on board. The SmartDriveDuo MDDS10, MDDS30 and MDDS60 drive two motors at 10, 30 and 60 A; the MDS40A and MDS160A drive one motor at 40 and 160 A. A DIP switch picks the input: RC receiver, analog joystick, PWM or serial, with optional mixed (tank) steering for robots.
Key specs at a glance
- Current
- MDDS10 10 A x2, MDDS30 30 A x2, MDDS60 60 A x2, MDS40A 40 A, MDS160A 160 A
- Motor supply
- 7 to 35 V (MDDS10, MDDS30), 7 to 45 V (MDDS60)
- Inputs
- RC (1-2 ms pulses), analog 0-5 V, PWM + DIR, simplified and packetized serial
- Mixed mode
- Joystick-style steering mixes speed and turn into both motors
- Protection
- Current limiting, temperature protection, battery low-voltage cut-off
- Logic
- 3.3 V and 5 V compatible
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Cytron SmartDriveDuo-30 (MDDS30) 30A Dual Motor Driver₹8,810
Option 2Cytron 10A 7V-35V SmartDrive Dual Channel DC Motor Driver (MDDS10)₹6,287
Option 3Cytron SmartDriveDuo-60A 7V-45V DC Motor Driver (MDDS60)₹20,668
Option 4Cytron SmartDrive MDS40A 40A Single Motor Driver₹8,599
Option 5Cytron SmartDrive MDS160A 160A Motor Driver₹27,405
What the Cytron SmartDrive MDDS30 is
SmartDrive boards suit combat and sumo robots, ride-on toys, wheelchairs and large RC vehicles. In RC mode you plug a receiver straight in and drive with no Arduino at all. In serial mode, one UART line controls both motors with a single byte per command.
Set the DIP switches with the power off; the board reads them at power-up.
Cytron SmartDrive MDDS30 pinout
The pins on the Cytron SmartDrive MDDS30 and what each one does.
| Pin | Function |
|---|---|
| B+ / B- | Battery |
| M1A / M1B, M2A / M2B | Motor terminals |
| IN1 / IN2 | Inputs for motor 1 and 2 (RC, analog or PWM depending on mode) |
| RC1 / RC2 | Receiver channel inputs with 5 V output for the receiver |
| TX / RX | Serial input (simplified serial uses RX only) |
| DIP switches | Input mode, mixed mode, baud rate and battery type |
- B+ / B-
- Battery
- M1A / M1B, M2A / M2B
- Motor terminals
- IN1 / IN2
- Inputs for motor 1 and 2 (RC, analog or PWM depending on mode)
- RC1 / RC2
- Receiver channel inputs with 5 V output for the receiver
- TX / RX
- Serial input (simplified serial uses RX only)
- DIP switches
- Input mode, mixed mode, baud rate and battery type
Wiring the Cytron SmartDrive MDDS30
In simplified serial mode the board only listens, so connect the controller TX to the driver's IN1/RX and join grounds. Set the matching baud rate on the DIP switches (9600 by default).
| Cytron SmartDrive MDDS30 pin | Arduino Uno | ESP32 |
|---|---|---|
| IN1 (serial RX) | D11 via SoftwareSerial TX | GPIO 17 (TX2) |
| GND | GND | GND |
| RC1 / RC2 (RC mode) | Receiver CH1 and CH2 | - |
| B+ / B- | Battery through fuse | Battery through fuse |
- IN1 (serial RX)
- Arduino Uno:
- D11 via SoftwareSerial TX
- ESP32:
- GPIO 17 (TX2)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- RC1 / RC2 (RC mode)
- Arduino Uno:
- Receiver CH1 and CH2
- ESP32:
- -
- B+ / B-
- Arduino Uno:
- Battery through fuse
- ESP32:
- Battery through fuse
Example code
Cytron also has the Cytron_SmartDriveDuo Arduino library for serial and PWM modes. Check your model's manual: the MDDS10 and MDDS60 use the same byte format.
#include <SoftwareSerial.h>
SoftwareSerial drv(10, 11); // RX (unused), TX to the driver
// Byte format: bit7 = motor (0 = left, 1 = right), bit6 = direction, bits 0-5 = speed 0-63
void motor(byte m, int speed) { // speed -63 to 63
byte b = (m << 7) | ((speed < 0) << 6) | (abs(speed) & 0x3F);
drv.write(b);
}
void setup() {
drv.begin(9600);
delay(2000); // let the driver detect the baud rate
}
void loop() {
motor(0, 40); motor(1, 40); delay(2000); // forward
motor(0, -40); motor(1, 40); delay(800); // turn
motor(0, 0); motor(1, 0); delay(2000);
}Setup and tuning
set input mode, mixed or independent, battery type and baud rate before power-up.
calibrate the transmitter's centre and end points using the board's set button.
select Li-Po or lead-acid so the board protects the battery.
use thick silicone wire and an XT60 or Anderson connector; add a main switch or fuse.
What you need
Shop this list9 of 11 found in our store · ₹72,713
Cytron SmartDriveDuo-30 (MDDS30) 30A Dual Motor Driver: the part this guide coversCytron SmartDriveDuo-30 (MDDS30) 30A Dual Motor Driver₹8,810
Cytron 10A 7V-35V SmartDrive Dual Channel DC Motor Driver (MDDS10): another version this guide coversCytron 10A 7V-35V SmartDrive Dual Channel DC Motor Driver (MDDS10)₹6,287
Cytron SmartDriveDuo-60A 7V-45V DC Motor Driver (MDDS60): another version this guide coversCytron SmartDriveDuo-60A 7V-45V DC Motor Driver (MDDS60)₹20,668
Cytron SmartDrive MDS40A 40A Single Motor Driver: another version this guide coversCytron SmartDrive MDS40A 40A Single Motor Driver₹8,599
Cytron SmartDrive MDS160A 160A Motor Driver: another version this guide coversCytron SmartDrive MDS160A 160A Motor Driver₹27,405- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
7.4V 2S Li-Po battery: to power the motors7.4V 3800mAh 2S Li-Po Battery (114253)₹373- Fuse holder: to protect the battery wiringFind this part
Automotive blade fuse: sized just above the motor currentAutomotive Blade Fuse₹5
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- Cytron MDD10A dual driver: simpler PWM + DIR only.
- High-current motor drivers: big driver types compared.
- BLDC motors and ESCs: for brushless motors instead.
Common mistakes to avoid
- Changing DIP switches with the power on.
- Leaving the low-voltage cut-off set for the wrong battery.
- Expecting replies in simplified serial mode: it only listens.
- Using it for brushless motors.
Frequently asked questions
Can I use it without an Arduino?
Yes. RC mode takes a receiver directly, and analog mode takes a joystick or potentiometers.
What is mixed mode?
One input sets forward speed and the other sets turning, and the board mixes them into both motors like a tank.
MDDS30 or MDDS60?
Choose by the motors' continuous current: up to 30 A per motor for the MDDS30, up to 60 A for the MDDS60.
Which serial format should I use?
Simplified serial for one board; packetized serial when several boards share one line.
Does it brake the motors?
Yes, zero speed brakes; it also limits current under stall.
Parts for this guide
Keep learning
Sources
- Cytron SmartDriveDuo MDDS10, MDDS30, MDDS60 user manuals
- Cytron SmartDrive MDS40A and MDS160A user manuals
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


