Component guide · Intermediate · 4 min read
ESP32 Cellular Boards

T-Call SIM800L, T-SIM7000G, SIM7670G and A7670E
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These boards put an ESP32 and a cellular modem on one PCB with a SIM holder, antenna connectors and battery charging, so you can build a tracker or remote sensor with no wiring. The T-Call uses a 2G SIM800L; the T-SIM7000G uses LTE-M/NB-IoT; the SIM7600, SIM7670G and A7670E boards use 4G Cat-1 or Cat-4, several with GNSS and a camera connector. Program them in Arduino IDE and drive the modem with TinyGSM.
Key specs at a glance
- T-Call SIM800L
- ESP32 + SIM800L 2G, IP5306 power chip
- T-SIM7000G
- ESP32-WROVER + SIM7000G LTE-M/NB-IoT + GNSS, 18650 and solar input
- T-SIM7600
- ESP32-WROVER + SIM7600E-H Cat-4 + GNSS, 18650 and solar
- ESP32-S3 SIM7670G
- LilyGO and Waveshare boards, Cat-1 + GNSS, camera connector on Waveshare
- Waveshare A7670E
- ESP32-S3 + A7670E Cat-1, camera connector
- Programming
- USB (CH9102 or native USB on S3)
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1LilyGO T-Call ESP32 SIM800L 2G Module w/ PMU & Antenna₹3,039
Option 2T-Call V1.4 ESP32 SIM800L GSM Module Unsoldered₹1,939
Option 3LilyGO TSIM7000G ESP32-WROVER-E Cellular IoT Dev Board w/ Solar & 18650₹7,349
Option 4LilyGO SIM7600E-H ESP32 WROVER-E Solar Charge Dev Board w/ 18650 Battery Holder₹10,499
Option 5LilyGO ESP32-S3 SIM7670G 4G LTE Cat-1 & GNSS Development Board₹5,979
Option 6Waveshare ESP32-S3 SIM7670G 4G LTE & GNSS Development Board w/ Camera₹5,769
What the ESP32 cellular board is
Check the network first: SIM800L needs 2G (not on Jio); SIM7000G needs an operator with LTE-M or NB-IoT, which is limited in India; Cat-1 and Cat-4 boards work on normal 4G SIMs. A7670E and SIM7670G target Europe and global bands; confirm Indian band support (B3, B5, B40) for your board before use.
Each board's pin map for MODEM_TX, MODEM_RX, PWRKEY and power-enable is fixed; copy it from the maker's example sketch.
ESP32 cellular board pinout
The pins on the ESP32 cellular board and what each one does.
| Pin | Function |
|---|---|
| MODEM_TX / MODEM_RX | ESP32 pins wired to the modem (board-specific) |
| MODEM_PWRKEY | Power-on pin |
| MODEM_POWER_ON / DTR | Modem power enable and sleep control on some boards |
| Battery | 18650 holder or JST Li-Po input |
| Solar | 5 to 6 V solar input on T-SIM7000G and T-SIM7600 |
| Antennas | LTE and GNSS IPEX connectors |
- MODEM_TX / MODEM_RX
- ESP32 pins wired to the modem (board-specific)
- MODEM_PWRKEY
- Power-on pin
- MODEM_POWER_ON / DTR
- Modem power enable and sleep control on some boards
- Battery
- 18650 holder or JST Li-Po input
- Solar
- 5 to 6 V solar input on T-SIM7000G and T-SIM7600
- Antennas
- LTE and GNSS IPEX connectors
Wiring the ESP32 cellular board
Pins above are for the T-Call V1.4; other boards use different pins, so always start from the maker's example. Fit antennas before power-up and keep a charged battery connected during transmit; USB alone may not supply the 2 A peaks.
| ESP32 cellular board pin | T-Call SIM800L | Other boards |
|---|---|---|
| Modem UART | Built in (TX 27, RX 26) | Built in (see board pin map) |
| PWRKEY | GPIO 4 | Board-specific |
| Power enable | GPIO 23 | Board-specific |
| Sensors | Free GPIOs: 13, 14, 15, 18, 19, 21, 22 | Free GPIOs per board map |
- Modem UART
- T-Call SIM800L:
- Built in (TX 27, RX 26)
- Other boards:
- Built in (see board pin map)
- PWRKEY
- T-Call SIM800L:
- GPIO 4
- Other boards:
- Board-specific
- Power enable
- T-Call SIM800L:
- GPIO 23
- Other boards:
- Board-specific
- Sensors
- T-Call SIM800L:
- Free GPIOs: 13, 14, 15, 18, 19, 21, 22
- Other boards:
- Free GPIOs per board map
Example code
Change the modem define and pins for your board, and the APN for your SIM. TinyGsmClient then works with PubSubClient for MQTT and ArduinoHttpClient for HTTP.
#define TINY_GSM_MODEM_SIM800 // SIM7000, SIM7600, A7670 for other boards
#include <TinyGsmClient.h>
#define MODEM_TX 27
#define MODEM_RX 26
#define MODEM_PWRKEY 4
#define MODEM_POWER_ON 23
HardwareSerial SerialAT(1);
TinyGsm modem(SerialAT);
void setup() {
Serial.begin(115200);
pinMode(MODEM_POWER_ON, OUTPUT); digitalWrite(MODEM_POWER_ON, HIGH);
pinMode(MODEM_PWRKEY, OUTPUT);
digitalWrite(MODEM_PWRKEY, LOW); delay(1000); digitalWrite(MODEM_PWRKEY, HIGH);
SerialAT.begin(115200, SERIAL_8N1, MODEM_RX, MODEM_TX);
delay(3000);
modem.restart();
Serial.println(modem.getModemInfo());
modem.waitForNetwork(60000);
Serial.print("Operator: "); Serial.println(modem.getOperator());
Serial.print("Signal: "); Serial.println(modem.getSignalQuality());
modem.gprsConnect("airtelgprs.com");
Serial.println(modem.isGprsConnected() ? "Data up" : "No data");
}
void loop() {}Setup and tuning
ESP32 core 2.x or 3.x; choose "ESP32 Wrover Module" for WROVER boards and enable PSRAM.
LilyGO and Waveshare GitHub repositories have tested sketches for each board.
solar boards charge the 18650 from a 5 to 6 V panel; use deep sleep between reports.
confirm Indian band support before buying an E (Europe) version.
What you need
Shop this list10 of 11 found in our store · ₹29,978
LilyGO T-Call ESP32 SIM800L 2G Module w/ PMU & Antenna: the part this guide coversLilyGO T-Call ESP32 SIM800L 2G Module w/ PMU & Antenna₹3,039
T-Call V1.4 ESP32 SIM800L GSM Module Unsoldered: another version this guide coversT-Call V1.4 ESP32 SIM800L GSM Module Unsoldered₹1,939
LilyGO TSIM7000G ESP32-WROVER-E Cellular IoT Dev Board w/ Solar & 18650: another version this guide coversLilyGO TSIM7000G ESP32-WROVER-E Cellular IoT Dev Board w/ Solar & 18650₹7,349
LilyGO SIM7600E-H ESP32 WROVER-E Solar Charge Dev Board w/ 18650 Battery Holder: another version this guide covers18650 Battery Holder₹29
LilyGO ESP32-S3 SIM7670G 4G LTE Cat-1 & GNSS Development Board: another version this guide coversLilyGO ESP32-S3 SIM7670G 4G LTE Cat-1 & GNSS Development Board₹5,979
Waveshare ESP32-S3 SIM7670G 4G LTE & GNSS Development Board w/ Camera: another version this guide coversWaveshare ESP32-S3 SIM7670G 4G LTE & GNSS Development Board w/ Camera₹5,769
Waveshare ESP32-S3 A7670E LTE 4G Development Board w/ Camera: another version this guide coversWaveshare ESP32-S3 A7670E LTE 4G Development Board w/ Camera₹5,209- 18650 Li-ion cell: a battery that can deliver the 2 A peaksFind this part
GSM antenna with 1 m cable and SMA plug: for better signal than the stub antennaGSM Antenna SMA 5cm 900-1800MHz 2dBi₹46Closest match, check the specs
GPS antenna 1575.42 MHz with SMA: an active GPS antenna for the GNSS inputGPS Antenna 1575.42MHz SMA Male 3M Cable₹279Closest match, check the specs
DS18B20 waterproof temperature probe: a sensor to report over 4GSonoff DS18B20 Waterproof Temperature Sensor Probe w/ 1m Cable – 1-Wire Interface₹340Closest match, check the specs
Alternatives and when to choose them
- A7672S 4G module: a separate 4G modem for your own ESP32.
- SIM800L GSM: the 2G modem on the T-Call.
- ESP32: the main controller.
Common mistakes to avoid
- Buying a 2G or NB-IoT board for a network that does not support it.
- Copying pins from a different board's sketch.
- Running on USB only and getting modem brown-outs.
- Leaving PSRAM off on WROVER boards with camera code.
Frequently asked questions
Which board works on Jio?
A Cat-1 or Cat-4 board with Indian LTE bands; not the SIM800L T-Call.
Can I add a camera?
Yes on the Waveshare ESP32-S3 4G boards with a camera connector.
How long does it run on an 18650?
Days to weeks with deep sleep between short reports; hours if the modem stays on.
Which library should I use?
TinyGSM, with the modem define for your board.
Do these have GPS?
The T-SIM7000G, T-SIM7600 and SIM7670G boards do; the T-Call does not.
Parts for this guide
Keep learning
Sources
- LilyGO T-Call, T-SIM7000G and T-SIM7600 documentation
- Waveshare ESP32-S3 SIM7670G and A7670E wiki
- TinyGSM library
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



