Component guide · Beginner · 3 min read
Flex, Force-Sensing and Thin-Film Tactile Sensors
FSR, Bend Sensors and Pressure Arrays
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Flex and force sensors are thin resistive strips whose resistance changes with bending or pressing. Read them with a voltage divider into an ADC pin. They are good for detecting presses, grip or bending, not for exact weights. Choose the force range, size and shape, protect the sensor from sharp edges and calibrate against known loads.
Key specs at a glance
- Force range
- About 20 g to 10 kg depending on model
- Types
- FSR discs, long strips, 16-zone films, tactile matrix arrays
- Output
- Resistance; analog via divider, or UART on array boards
- Thickness
- Under 0.5 mm on thin films
- Operating temp
- Up to about 120 °C on some models
- Accuracy
- Rough: ±10% or worse; best for detection
Which sensor
Select by what you need to feel.
| Sensor | Senses | Notes |
|---|---|---|
| FSR402-style disc | Pressure on a small round area | Cheap; very popular |
| Long-tail FSR strips (FSR407) | Pressure on a long strip | Good for mounting inside shoes |
| Thin circular film (DFRobot) | Small forces on 0.45 mm film | Fits tight spaces |
| 16-zone flexible film | Pressure in several zones | Needs multiple ADC channels |
| Tactile matrix (4x8, 6x6) | Pressure map | UART output on DFRobot boards |
| Bend/flex sensor | Bending angle | Resistance rises as it bends |
- FSR402-style disc
- Senses:
- Pressure on a small round area
- Notes:
- Cheap; very popular
- Long-tail FSR strips (FSR407)
- Senses:
- Pressure on a long strip
- Notes:
- Good for mounting inside shoes
- Thin circular film (DFRobot)
- Senses:
- Small forces on 0.45 mm film
- Notes:
- Fits tight spaces
- 16-zone flexible film
- Senses:
- Pressure in several zones
- Notes:
- Needs multiple ADC channels
- Tactile matrix (4x8, 6x6)
- Senses:
- Pressure map
- Notes:
- UART output on DFRobot boards
- Bend/flex sensor
- Senses:
- Bending angle
- Notes:
- Resistance rises as it bends
Wiring with a voltage divider
Connect the sensor between 3.3 V (or 5 V) and an ADC pin, and a fixed resistor (about 10 kΩ) from the pin to ground. As force increases the sensor's resistance falls and the ADC voltage rises. Choose the fixed resistor to set the sensitivity; see the voltage divider tool and ADC basics. Add a small capacitor to smooth noise. See the broader force-sensitive resistor guide.
Calibration
Press with known weights, record the ADC value for each, and fit a curve. The response is not linear, so use a table or a fitted curve. Expect drift and hysteresis: the same load can read differently over time. For accurate weighing use a load cell.
Mounting tips
- Press on the active area only; avoid the leads.
- Use a flat, compliant surface, such as a rubber pad, to spread force.
- Do not bend FSR strips sharply at the lead crimp.
- Cover with tape to protect from sweat and scratches.
- For arrays, use a firm, flat backing.
Project ideas
Smart insoles, grip-strength meters, glove-bend sensing for hand tracking, touch-sensitive keys, pressure maps for chairs and robot grippers. For simple touch use touch sensors.
Try it: Voltage divider calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Expecting accurate weight from an FSR.
- Using the wrong fixed resistor and saturating the ADC.
- Folding the sensor at the lead.
- Concentrating force on a tiny point and damaging the film.
- Skipping calibration.
Frequently asked questions
What is an FSR?
A force-sensing resistor whose resistance drops when pressed.
Can I weigh things with an FSR?
Only roughly. Use a load cell for accuracy.
What resistor do I use?
Start with 10 kΩ and adjust for sensitivity.
How do tactile arrays connect?
Some have a UART output; others need multiplexing.
Do FSRs drift?
Yes, so calibrate and expect some hysteresis.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 2 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






