Buying guide · Intermediate · 3 min read
Load Cells and Strain Gauges
Bar, S-Type, Platform and Button Cells
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A load cell is a metal block with strain gauges that change resistance under load. Pick the shape for your mounting (bar cells for scales, S-type for hanging loads, platform cells for bench scales), choose a capacity about 1.5 to 2 times the maximum load, and read it with an HX711 or similar 24-bit amplifier. Mount it so force flows only along its sensing axis.
Key specs at a glance
- Bar / single-point
- Small scales and kitchen scales, 1 to 200 kg
- S-type
- Tension and compression, hanging scales and tank weighing
- Button / pancake
- Compression only, high capacity and low height
- Platform
- Bench scale with a flat top
- Output
- About 1 to 3 mV/V; 2 mV/V is typical
- Wiring
- Four wires (excitation and signal), sometimes six with sense wires
Which load cell shape
Mounting and load direction decide the type.
| Type | Load direction | Good for | Notes |
|---|---|---|---|
| Bar (beam) cell | Bending | Kitchen and shelf scales, DIY platforms | Use four for a platform |
| Single-point platform | Off-centre load on a plate | Small bench scales | Insensitive to load position |
| S-type | Tension or compression | Hanging scales, tank weighing | Hooks or rod ends needed |
| Button / pancake | Compression | Presses, heavy machines | Needs a flat, aligned load |
| Shear beam | Bending | Platform scales, hoppers | Robust, high capacity |
- Bar (beam) cell
- Load direction:
- Bending
- Good for:
- Kitchen and shelf scales, DIY platforms
- Notes:
- Use four for a platform
- Single-point platform
- Load direction:
- Off-centre load on a plate
- Good for:
- Small bench scales
- Notes:
- Insensitive to load position
- S-type
- Load direction:
- Tension or compression
- Good for:
- Hanging scales, tank weighing
- Notes:
- Hooks or rod ends needed
- Button / pancake
- Load direction:
- Compression
- Good for:
- Presses, heavy machines
- Notes:
- Needs a flat, aligned load
- Shear beam
- Load direction:
- Bending
- Good for:
- Platform scales, hoppers
- Notes:
- Robust, high capacity
Reading the specification
Capacity is the maximum load; choose about 1.5 to 2 times your largest expected weight. Sensitivity is usually 2 mV/V, so 5 V excitation gives 10 mV at full load. Accuracy is quoted as non-linearity and hysteresis. Overload is the maximum safe load without damage. Temperature drift and creep also matter for precise work.
Reading with an HX711
The HX711 is a 24-bit amplifier made for load cells. Connect the red wire to E+, black to E−, white to A− and green to A+ (check your cell's colours, as they vary). Use a library to read raw values, tare with no load and calibrate with a known weight to find a scale factor. The details are in the HX711 guide and the load cell calculator.
Mounting for accuracy
- Mount the fixed end rigidly and apply load at the free end only.
- Keep the load vertical and centred. Side forces cause errors.
- Add overload stops for platforms that can be stepped on.
- Protect the cell from moisture and keep the cable relieved.
- Allow a few minutes of warm-up and keep temperature stable for precise work.
Try it: Load cell hx711 calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Choosing a capacity close to the maximum load.
- Mounting the cell so it twists.
- Swapping signal wires and getting inverted readings.
- Skipping tare and calibration.
- Exposing the cell to water or overload.
Frequently asked questions
How do I know the wiring colours?
Check the load cell data sheet. Red and black are usually excitation; white and green are signal.
How many bar cells for a platform?
Four, wired as a bridge with a combiner board, or use a single-point cell.
Can I use a 50 kg cell for 5 kg?
Yes, but resolution is lower. Pick a closer capacity for fine work.
What is mV/V?
Output per volt of excitation at full load. 2 mV/V is typical.
Why does my reading drift?
Temperature changes, loose mounting or a noisy supply.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 25 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




