Component guide · Intermediate · 5 min read
I2C Pressure Sensors

Sencoch GZP6847D, GZP6857D, GZP6859D, GZP6869D, GZP6816D and WFSensor WF100DPZ, WF5803F, WF183DE
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These are the digital versions of the GZP and WF pressure sensors: the D in the part code means a calibrated I2C output, so you get pressure and temperature as numbers. They run at 3.3 V and draw almost nothing between readings, which suits battery devices. Ranges run from 5 kPa to 1500 kPa; the WF5803F and WF183DE also handle high pressure and liquids in sealed packages.
Key specs at a glance
- Interface
- I2C (address usually 0x6D); SPI on some WF parts
- Supply
- 3.3 V (1.8 to 3.6 V)
- Resolution
- 24-bit pressure, 16-bit temperature
- Range
- 0 to 5 kPa up to 1500 kPa; vacuum versions
- Standby
- About 100 nA
- Package
- DIP-6, SOP-6, SOP-8, LGA
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Sencoch GZP6859D101KPP Pressure Sensor, 0-100 kPa, 3.3V, I2C, SOP-6-2.54mm₹549
Option 2Sencoch GZP6847D101KPN Pressure Sensor, 0-100 kPa, 3.3V, I²C, DIP-6₹619
Option 3WFSensor GZP6847D701KPP Differential Pressure Sensor, 0-700 kPa, 3.3V, I2C, DIP-6₹689
Option 4Sencoch GZP6857D005KPP I²C Digital Pressure Sensor, 3.3V, 100nA, DIP-6, Range: 0–5 kPa₹589
Option 5Sencoch GZP6857D040KPP Digital Pressure Sensor, I2C, 3.3V, Ultra-Low Power, Range: 0-40 kPa₹509
Option 6Sencoch GZP6857D101KPN Pressure Sensor, -100kPa~0kPa, 3.3V, 100nA, I2C₹529
What the GZP6847D, GZP6857D, GZP6859D and WF digital pressure sensors is
GZP I2C digital pressure sensors such as the GZP6816D and GZP6859D give calibrated pressure and temperature over I2C, used in weather, altitude and pneumatic projects.
You start a conversion by writing to register 0x30, wait until it finishes, then read three bytes of pressure and two of temperature. Divide the raw pressure by a range factor (K) given in the datasheet for your full scale.
Run an I2C scan first; if 0x6D does not answer, check the datasheet for your exact part.
GZP6847D, GZP6857D, GZP6859D and WF digital pressure sensors pinout
The pins on the GZP6847D, GZP6857D, GZP6859D and WF digital pressure sensors and what each one does.
| Pin | Function |
|---|---|
| VDD | 3.3 V |
| GND | Ground |
| SDA | I2C data |
| SCL | I2C clock |
| CSB / SDO | SPI on some parts |
- VDD
- 3.3 V
- GND
- Ground
- SDA
- I2C data
- SCL
- I2C clock
- CSB / SDO
- SPI on some parts
Wiring the GZP6847D, GZP6857D, GZP6859D and WF digital pressure sensors
Bare sensors are SMD or DIP parts: solder them to a PCB or adapter, power them at the voltage in the part number (3.3 or 5 V) and keep tube ports clear of solder and flux. These are 3.3 V parts: use a level shifter with a 5 V Uno.
| GZP6847D, GZP6857D, GZP6859D and WF digital pressure sensors pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5V (or 3.3V) | 3V3 |
| GND | GND | GND |
| SDA | A4 | GPIO 21 |
| SCL | A5 | GPIO 22 |
- VCC
- Arduino Uno:
- 5V (or 3.3V)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SDA
- Arduino Uno:
- A4
- ESP32:
- GPIO 21
- SCL
- Arduino Uno:
- A5
- ESP32:
- GPIO 22
Example code
Set K from the datasheet table for your range; WF5803F and WF183DE use their own registers.
// GZP68xxD / XGZP-style I2C pressure sensor at 0x6D
#include <Wire.h>
const uint8_t ADDR = 0x6D;
const float K = 64; // range factor from the datasheet table (depends on full scale)
void wr(uint8_t r, uint8_t v) { Wire.beginTransmission(ADDR); Wire.write(r); Wire.write(v); Wire.endTransmission(); }
uint8_t rd(uint8_t r) { Wire.beginTransmission(ADDR); Wire.write(r); Wire.endTransmission(false); Wire.requestFrom(ADDR, (uint8_t)1); return Wire.read(); }
void setup() { Serial.begin(115200); Wire.begin(); }
void loop() {
wr(0x30, 0x0A); // start pressure + temperature conversion
while (rd(0x30) & 0x08) delay(1); // wait for conversion to finish
long p = ((long)rd(0x06) << 16) | ((long)rd(0x07) << 8) | rd(0x08);
if (p & 0x800000) p -= 0x1000000; // signed 24-bit
int t = (rd(0x09) << 8) | rd(0x0A);
Serial.print("Pressure "); Serial.print(p / K, 1); Serial.print(" Pa Temp ");
Serial.print(t / 256.0, 1); Serial.println(" C");
delay(200);
}Setup and tuning
connect SDA, SCL, VCC and GND; most run at 3.3 V, so check the rating before using 5 V.
read the I2C address from the datasheet and scan the bus if unsure.
add 4.7 kΩ pull-ups if the board does not have them.
send the measure command, wait, then read pressure and temperature bytes.
protect the pressure port from water and dust.
What you need
Shop this list20 of 20 found in our store · ₹10,700
Sencoch GZP6859D101KPP Pressure Sensor, 0-100 kPa, 3.3V, I2C, SOP-6-2.54mm: the part this guide coversSencoch GZP6859D101KPP Pressure Sensor, 0-100 kPa, 3.3V, I2C, SOP-6-2.54mm₹549
Sencoch GZP6847D101KPN Pressure Sensor, 0-100 kPa, 3.3V, I²C, DIP-6: another version this guide coversSencoch GZP6847D101KPN Pressure Sensor, 0-100 kPa, 3.3V, I²C, DIP-6₹619
WFSensor GZP6847D701KPP Differential Pressure Sensor, 0-700 kPa, 3.3V, I2C, DIP-6: another version this guide coversWFSensor GZP6847D701KPP Differential Pressure Sensor, 0-700 kPa, 3.3V, I2C, DIP-6₹689
Sencoch GZP6857D005KPP I²C Digital Pressure Sensor, 3.3V, 100nA, DIP-6, Range: 0–5 kPa: another version this guide coversSencoch GZP6857D005KPP I²C Digital Pressure Sensor, 3.3V, 100nA, DIP-6, Range: 0–5 kPa₹589
Sencoch GZP6857D040KPP Digital Pressure Sensor, I2C, 3.3V, Ultra-Low Power, Range: 0-40 kPa: another version this guide coversSencoch GZP6857D040KPP Digital Pressure Sensor, I2C, 3.3V, Ultra-Low Power, Range: 0-40 kPa₹509
Sencoch GZP6857D101KPN Pressure Sensor, -100kPa~0kPa, 3.3V, 100nA, I2C: another version this guide coversSencoch GZP6857D101KPN Pressure Sensor, -100kPa~0kPa, 3.3V, 100nA, I2C₹529
Sencoch GZP6857D201KPP Digital Pressure Sensor, I2C, 3.3V, Low Power, Range: 0-200 kPa: another version this guide coversSencoch GZP6857D201KPP Digital Pressure Sensor, I2C, 3.3V, Low Power, Range: 0-200 kPa₹689
Sencoch GZP6859D005KPP MEMS Pressure Sensor, 0-5 kPa Range, 3.3V I2C Output, SOP-6 Package: another version this guide coversSencoch GZP6859D005KPP MEMS Pressure Sensor, 0-5 kPa Range, 3.3V I2C Output, SOP-6 Package₹569
Sencoch GZP6859D040KPP Pressure Sensor, 0-40 kPa Range, 3.3V, I²C Output, Ultra-Low Power (100 nA), SOP-6 Package: another version this guide coversSencoch GZP6859D040KPP Pressure Sensor, 0-40 kPa Range, 3.3V, I²C Output, Ultra-Low Power (100 nA), SOP-6 Package₹489
Sencoch GZP6859D201KPP Pressure Sensor, 0-200 kPa, 3.3V, 100nA, I2C: another version this guide coversSencoch GZP6859D201KPP Pressure Sensor, 0-200 kPa, 3.3V, 100nA, I2C₹449
Sencoch GZP6869D010KPP Digital Pressure Sensor, I2C, 3.3V, 0-10 kPa Range: another version this guide coversSencoch GZP6869D010KPP Digital Pressure Sensor, I2C, 3.3V, 0-10 kPa Range₹649
Sencoch GZP6869D200KPP Digital Pressure Sensor, 0-200 kPa Range, I2C Interface, SOP-8 Package: another version this guide coversSencoch GZP6869D200KPP Digital Pressure Sensor, 0-200 kPa Range, I2C Interface, SOP-8 Package₹569
Sencoch GZP6816D Pressure Sensor, 30Kpa~110Kpa Range, 3.3V I2C: another version this guide coversSencoch GZP6816D Pressure Sensor, 30Kpa~110Kpa Range, 3.3V I2C₹59
WFSensor WF100DPZ 0.1BG D6 DT DIP-6 Pressure Sensor – I2C/SPI, 40 kPa Gauge: another version this guide coversWFSensor WF100DPZ 0.1BG D6 DT DIP-6 Pressure Sensor – I2C/SPI, 40 kPa Gauge₹249
WFSensor WF100DPZ 10BG S6 DT Digital Pressure Sensor, Gauge Type, SMD-6P 6×6 mm, Range: 0-1000 kPa: another version this guide coversWFSensor WF100DPZ 10BG S6 DT Digital Pressure Sensor, Gauge Type, SMD-6P 6×6 mm, Range: 0-1000 kPa₹289
WFSensor WF100DPZ 1BG S6 DT Digital Pressure Sensor, 0-10 kPa, I2C/SPI, SOP-6-2.54mm: another version this guide coversWFSensor WF100DPZ 1BG S6 DT Digital Pressure Sensor, 0-10 kPa, I2C/SPI, SOP-6-2.54mm₹219
WFSensor WF100DPZ-1BG Pressure Sensor (100 kPa), DTSOP-6, RoHS: another version this guide coversWFSensor WF100DPZ-1BG Pressure Sensor (100 kPa), DTSOP-6, RoHS₹219
WFSensor WF5803F 20BA L8 DT MEMS Gauge Pressure Sensor – LGA-6 (6.2×6.8 mm), I2C/SPI, 30-2000 kPa: another version this guide coversWFSensor WF5803F 20BA L8 DT MEMS Gauge Pressure Sensor – LGA-6 (6.2×6.8 mm), I2C/SPI, 30-2000 kPa₹1,259
WFSensor WF5803F 30BA L8 DT Digital Pressure Sensor, 30-700 kPa, 1.8-3.6V, I2C/SPI, LGA-8: another version this guide coversWFSensor WF5803F 30BA L8 DT Digital Pressure Sensor, 30-700 kPa, 1.8-3.6V, I2C/SPI, LGA-8₹1,389
WFSensor WF183DE 15BA L8B Air Pressure & Temperature Sensor, 0~1500kPa, 2.4V~5.5V, 2uA, -40℃~+125℃: another version this guide coversWFSensor WF183DE 15BA L8B Air Pressure & Temperature Sensor, 0~1500kPa, 2.4V~5.5V, 2uA, -40℃~+125℃₹119
Alternatives and when to choose them
- GZP analog sensors: voltage output.
- BMP390 and BMP581: barometric sensors.
- LPS22: ST barometer.
Common mistakes to avoid
- Running a 3.3 V sensor at 5 V.
- Leaving out I2C pull-ups.
- Blocking or wetting the pressure port.
- Using the wrong I2C address.
Frequently asked questions
How do I read a GZP I2C pressure sensor?
Send the measurement command over I2C, wait, then read the pressure and temperature registers.
Can I use it at 5 V?
Only if the datasheet allows it; many are 3.3 V parts.
Can it measure altitude?
Yes. Barometric models convert pressure to altitude with a formula.
Why does the sensor not show up on the I2C bus?
Check wiring, pull-ups and the address from the datasheet.
Does temperature affect readings?
The sensor compensates internally, but avoid fast temperature changes.
Parts for this guide
- ₹549View
- ₹619View
- ₹689View
- ₹589View
- ₹509View
- ₹529View
- ₹689View
- ₹569View
Sencoch GZP6859D040KPP Pressure Sensor, 0-40 kPa Range, 3.3V, I²C Output, Ultra-Low Power (100 nA), SOP-6 Package₹489View- ₹449View
- ₹649View
- ₹569View
- ₹59View
- ₹249View
- ₹289View
- ₹219View
- ₹219View
- ₹1,259View
- ₹1,389View
- ₹119View
- ₹389View
- ₹359View
- ₹20View
- ₹128View
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




