Component guide · Intermediate · 4 min read
HB100, CDM324, Grove BGT24LTR11 and 10.525 GHz Doppler Radar Modules

Motion and Speed Sensing
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The HB100 (10.525 GHz) and CDM324 (24 GHz) are Doppler radar front ends. They send a constant microwave signal and output a tiny IF signal whose frequency rises with the target's speed. The bare modules need an amplifier before a microcontroller can count it; the DFRobot, HaiWang and Grove versions add the amplifier and give a digital or serial output.
Key specs at a glance
- Frequency
- 10.525 GHz (HB100, DFRobot), 24.125 GHz (CDM324, BGT24LTR11)
- Supply
- 5 V (HB100 bare), 6 to 24 V (HaiWang), 3.3 to 5 V (Grove)
- Output
- IF signal in microvolts to millivolts (bare); digital or UART (boards)
- Range
- About 2 to 20 m for people, more for cars
- Doppler shift
- About 19.5 Hz per km/h at 10.525 GHz, 44.7 Hz per km/h at 24 GHz
- Detection
- Moving targets only
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1HB100 Microwave Doppler Radar Motion Sensor Module₹197
Option 2HaiWang HW-HB100 Microwave Radar Sensor Module, 10-30m Range, 10.525GHz, 6-24V DC₹1,289
Option 3HaiWang HW-HB100L Microwave Radar Motion Sensor Module – 10-35m Range, IP65 Waterproof Casing₹1,529
Option 4DFRobot Gravity Digital 10.525 GHz Microwave Sensor Motion Detection Module₹1,103
Option 5CDM324 24GHz Microwave Radar Motion Sensor₹820
Option 6Elecrow Crowtail Microwave Sensor 2.0 – 3kHz Doppler Radar, 4m Range, 5V DC₹669
What the HB100, CDM324 and 10.525 GHz Doppler radar modules is
The HB100 (10.525 GHz) and CDM324 (24 GHz) are Doppler radar modules that output a small signal whose frequency equals how fast a target moves toward or away from them.
A Doppler radar only sees things that move. The IF frequency tells you the speed along the line of sight, so a car crossing in front reads slower than one coming straight at you.
The bare HB100 IF output is too small for a digital pin. Use a two-stage op-amp amplifier (the HB100 application note shows one) or buy an amplified module. The Grove BGT24LTR11 board has its own microcontroller and reports speed and direction over UART.
HB100, CDM324 and 10.525 GHz Doppler radar modules pinout
The pins on the HB100, CDM324 and 10.525 GHz Doppler radar modules and what each one does.
| Pin | Function |
|---|---|
| VCC / +5V | Supply |
| GND | Ground |
| IF | Doppler output (bare modules, needs amplifying) |
| OUT / D | Digital motion or squared IF output (amplified boards) |
| TX / RX | UART (Grove BGT24LTR11) |
- VCC / +5V
- Supply
- GND
- Ground
- IF
- Doppler output (bare modules, needs amplifying)
- OUT / D
- Digital motion or squared IF output (amplified boards)
- TX / RX
- UART (Grove BGT24LTR11)
Wiring the HB100, CDM324 and 10.525 GHz Doppler radar modules
Amplified boards connect like this. A bare HB100 or CDM324 needs an op-amp stage between IF and the input pin.
| HB100, CDM324 and 10.525 GHz Doppler radar modules pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5 V | 5 V (VIN) or 3.3 V (check module) |
| GND | GND | GND |
| OUT | D2 | GPIO 27 |
- VCC
- Arduino Uno:
- 5 V
- ESP32:
- 5 V (VIN) or 3.3 V (check module)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- OUT
- Arduino Uno:
- D2
- ESP32:
- GPIO 27
Example code
Feed the pin from an amplifier and comparator, or from the digital output of an amplified board. The speed is only the component towards or away from the sensor.
// Doppler speed from an amplified IF output: count pulses for 250 ms
// Doppler shift: about 19.5 Hz per km/h at 10.525 GHz, 44.7 Hz per km/h at 24.125 GHz
const int IF_PIN = 2; // amplified, squared-up IF signal (interrupt pin)
const float HZ_PER_KMH = 19.5; // change to 44.7 for 24 GHz modules
volatile unsigned long pulses = 0;
void count() { pulses++; }
void setup() {
Serial.begin(115200);
pinMode(IF_PIN, INPUT);
attachInterrupt(digitalPinToInterrupt(IF_PIN), count, RISING);
}
void loop() {
pulses = 0;
delay(250);
float hz = pulses * 4.0;
if (hz > 20) {
Serial.print(hz, 0); Serial.print(" Hz ~");
Serial.print(hz / HZ_PER_KMH, 1); Serial.println(" km/h");
}
}Setup and tuning
feed 5 V from a clean supply; the modules are sensitive to supply noise.
the IF output is only microvolts to millivolts, so add an op-amp amplifier (often 1000× or more) before the microcontroller.
count the IF frequency; for the HB100, speed in km/h is about frequency in Hz divided by 19.5.
keep the antenna face clear; plastic covers are fine, metal is not.
check that 10.525 GHz or 24 GHz use is allowed where you live.
What you need
Shop this list9 of 11 found in our store · ₹14,782
HB100 Microwave Doppler Radar Motion Sensor Module: the part this guide coversHB100 Microwave Doppler Radar Motion Sensor Module₹197
HaiWang HW-HB100 Microwave Radar Sensor Module, 10-30m Range, 10.525GHz, 6-24V DC: another version this guide coversHaiWang HW-HB100 Microwave Radar Sensor Module, 10-30m Range, 10.525GHz, 6-24V DC₹1,289
HaiWang HW-HB100L Microwave Radar Motion Sensor Module – 10-35m Range, IP65 Waterproof Casing: another version this guide coversHaiWang HW-HB100L Microwave Radar Motion Sensor Module – 10-35m Range, IP65 Waterproof Casing₹1,529
DFRobot Gravity Digital 10.525 GHz Microwave Sensor Motion Detection Module: another version this guide coversDFRobot Gravity Digital 10.525 GHz Microwave Sensor Motion Detection Module₹1,103
CDM324 24GHz Microwave Radar Motion Sensor: another version this guide coversCDM324 24GHz Microwave Radar Motion Sensor₹820
Elecrow Crowtail Microwave Sensor 2.0 – 3kHz Doppler Radar, 4m Range, 5V DC: another version this guide coversElecrow Crowtail Microwave Sensor 2.0 – 3kHz Doppler Radar, 4m Range, 5V DC₹669
Seeed Studio Studio Grove Doppler Radar (BGT24LTR11) – 24GHz Motion & Velocity Sensor Module: another version this guide coversSeeed Studio Grove Doppler Radar (BGT24LTR11) – 24GHz Motion & Velocity Sensor Module₹8,759Closest match, check the specs
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- Uno R3 development board: the controller used in the wiring tableFind this part
RCWL-0516 microwave radar motion sensor: the cheapest microwave motion moduleRCWL-0516 Microwave Radar Motion Sensor Module₹27- Hi-Link HLK-LD2410 24 GHz presence radar: the most common hobby presence radarFind this part
Alternatives and when to choose them
- RCWL-0516 and LD2410: ready-made motion and presence modules.
- Microwave motion modules: 5.8 GHz switch modules.
- Speed radars: give speed directly over UART.
Common mistakes to avoid
- Connecting the IF output straight to an analog pin.
- Powering it from a noisy USB or switching supply.
- Mounting it behind metal.
- Expecting it to detect someone standing still.
Frequently asked questions
Why does the HB100 output look like noise?
The IF signal is tiny. Add an amplifier board and filter before reading it.
How do I convert the frequency to speed?
For the HB100, km/h is about the Doppler frequency in Hz divided by 19.5.
Can a Doppler radar detect a still person?
No. It only sees motion; use an FMCW presence radar for still people.
Can it see through plastic or walls?
It passes through plastic and thin wood, but not metal, and walls weaken it a lot.
Is the CDM324 better than the HB100?
It is smaller and works at 24 GHz, with a shorter wavelength and smaller antenna.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


