Comparison · Intermediate · 3 min read
mmWave Radar Modules
24 GHz and 60 GHz Presence, Fall and Trajectory Sensors
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
mmWave radar modules sense people by their tiny motions, including breathing, so they detect someone sitting still where a PIR sensor fails. 24 GHz modules such as the LD2410 handle presence and distance, while 60 GHz modules add finer breathing, sleep and fall detection. Power from 5 V, read the UART or output pin, and mount away from fans and moving curtains.
Key specs at a glance
- 24 GHz FMCW
- LD2410 class: moving and static presence, range to about 6 m
- 60 GHz
- Vital signs, fall detection, finer resolution
- Output
- Digital presence pin plus UART data
- Supply
- 5 V on most modules, 3.3 V logic
- Mounting
- Through plastic cases, no lens needed
- Privacy
- No camera; no images captured
Why use radar instead of PIR
A PIR sensor detects changes in infrared heat, so it needs movement. mmWave radar measures reflected radio waves and can detect the tiny movements of a person who is sitting or sleeping. It works through thin plastic, in the dark, and is not fooled by heat sources. See the mmWave guide and PIR sensors for a comparison.
24 GHz and 60 GHz modules
Pick the module for the task.
| Module type | Detects | Use for | Notes |
|---|---|---|---|
| 24 GHz presence (LD2410) | Moving and static people, distance | Lighting, occupancy, smart home | Adjustable gates and sensitivity |
| 24 GHz micro-motion | Very small movements | Desk and chair presence | Short range |
| 24 GHz trajectory (LD2460) | Position tracks of several targets | Counting and zoning | More complex output |
| 60 GHz fall detection | Posture changes and falls | Elder-care monitoring | Needs correct height and angle |
| 60 GHz vital signs | Breathing and heart rate estimates | Sleep monitoring | Not a medical device |
- 24 GHz presence (LD2410)
- Detects:
- Moving and static people, distance
- Use for:
- Lighting, occupancy, smart home
- Notes:
- Adjustable gates and sensitivity
- 24 GHz micro-motion
- Detects:
- Very small movements
- Use for:
- Desk and chair presence
- Notes:
- Short range
- 24 GHz trajectory (LD2460)
- Detects:
- Position tracks of several targets
- Use for:
- Counting and zoning
- Notes:
- More complex output
- 60 GHz fall detection
- Detects:
- Posture changes and falls
- Use for:
- Elder-care monitoring
- Notes:
- Needs correct height and angle
- 60 GHz vital signs
- Detects:
- Breathing and heart rate estimates
- Use for:
- Sleep monitoring
- Notes:
- Not a medical device
Wiring and reading
Power the module from 5 V and connect its TX to the microcontroller's RX (and RX to TX) at the module's baud rate; the LD2410 defaults to 256000 baud. The OUT pin goes high when a person is present, so the simplest use is to read it as a digital input. For distance and energy values, parse the UART frames or use an ESPHome or Arduino library. The module's gates set the distance bins and sensitivity, which you adjust to avoid false triggers. See UART.
Placement tips
- Mount at a height and angle shown in the data sheet and point it at the area to monitor.
- Keep it away from fans, curtains and pets that move in the zone.
- Metal blocks radar; plastic and thin walls do not.
- Use a stable 5 V supply, since noise causes false triggers.
- Radar is low power, but do not use it as a life-safety system.
Try it: Frequency wavelength calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Mounting near a fan or air vent and getting false triggers.
- Powering it from 3.3 V when it needs 5 V.
- Using the wrong baud rate in the code.
- Aiming at a window or moving curtain.
- Expecting medical accuracy from a hobby module.
Frequently asked questions
Can radar see through walls?
Thin plastic and drywall partly; thick walls and metal block it.
Is mmWave radar safe?
These modules use very low power, far below limits for exposure.
What is the range of LD2410?
About 6 m at best, depending on settings and the target.
Is it better than PIR?
For static presence, yes. PIR is cheaper and enough for simple motion lights.
Does it work with Home Assistant?
Yes through ESPHome or MQTT with an ESP32 reading the module.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 10 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




