LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA PIR sign flips to free as soon as people sit still in a meeting. The LD2410 radar sees them breathing, so the red light stays on for the whole meeting and switches to green 10 seconds after the last person leaves.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Millimetre-wave radar that detects whether a person is in the room, even if they sit completely still, which a PIR sensor cannot do.
Red indicator LED for the alert state.; Green indicator LED for the normal state.
Follow the colours: red is power, dark grey is ground, blue is a signal.
meeting_room_radar_in_use_sign.inoVerify & upload in Electrolark// Meeting room radar in-use sign
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "meeting-room-radar-in-use-sign"
// ---- pins ----
const uint8_t PRESENCE_PIN = 2;
const uint8_t LED_RED = 3;
const uint8_t LED_GREEN = 4;
// ---- latest readings ----
bool presence = false;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const unsigned long HOLD_MS = 10000; // stay on this long after the last trigger
unsigned long lastTrigger = 0;
const unsigned long WARMUP_MS = 30000UL; // sensor warm-up
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void evaluate() {
if (millis() < WARMUP_MS) { alertOn = false; statusText = "Warming up"; return; }
if (presence) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "IN USE" : "Free";
}
void setup() {
Serial.begin(115200);
pinMode(PRESENCE_PIN, INPUT);
pinMode(LED_RED, OUTPUT);
pinMode(LED_GREEN, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
presence = digitalRead(PRESENCE_PIN) == HIGH;
evaluate();
Serial.print(F("Presence="));
Serial.print(presence ? F("yes") : F("no"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setRedLed(alertOn && (millis() / 250) % 2 == 0);
setGreenLed(!alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Move the sensor away from fans, moving curtains and metal that vibrates, and give it a minute to settle.
Check it has 5 V on VCC and the OUT wire goes to the right pin.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), HLK-LD2410 24GHz Human Presence Radar Sensor Module – 5 m Range, 2 × Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 9 steps.
No. This page has the complete, tested code (meeting_room_radar_in_use_sign.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹694 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Current-limiting resistors for LEDs; Radar presence sensing.
Ideas that reuse this build: Washroom occupied sign and Study room presence light. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Presence=no, status=Warming up Presence=no, status=Warming up
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.