Component guide · Beginner · 3 min read
ISD1820 Voice Recorder Module

Pinout, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The ISD1820 module records one short voice message, 8 to 20 seconds depending on the resistor fitted, and plays it back through a small speaker. Press REC to record, PLAYE to play the whole message or hold PLAYL. It keeps the message without power, runs from 3 to 5 V, and an Arduino can trigger playback by pulling the PLAYE pin HIGH.
Key specs at a glance
- Message length
- About 10 s as supplied (8 to 20 s, set by the ROSC resistor)
- Supply
- 3 to 5 V
- Speaker output
- 8 ohm, about 0.5 W
- Storage
- Non-volatile, keeps the message without power
- Controls
- REC, PLAYE (edge), PLAYL (level) buttons and pins
- Microphone
- On-board electret
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
What the ISD1820 module is
The chip stores the sound as analog levels in its own memory, so it needs no SD card or code to record. It is useful for talking toys, a doorbell or reminder message, or announcing an alarm.
Only one message is stored. Recording again replaces it. For several messages or better quality, use a DFPlayer Mini with MP3 files.
ISD1820 module pinout
The pins on the ISD1820 module and what each one does.
| Pin | Function |
|---|---|
| VCC | Supply, 3 to 5 V |
| GND | Ground |
| REC | HIGH to record (hold for the length of the message) |
| PLAYE | A HIGH pulse plays the whole message |
| PLAYL | Plays while held HIGH |
| FT | Feed-through: mic goes straight to the speaker while HIGH |
| SP+ / SP- | Speaker, 8 ohm |
- VCC
- Supply, 3 to 5 V
- GND
- Ground
- REC
- HIGH to record (hold for the length of the message)
- PLAYE
- A HIGH pulse plays the whole message
- PLAYL
- Plays while held HIGH
- FT
- Feed-through: mic goes straight to the speaker while HIGH
- SP+ / SP-
- Speaker, 8 ohm
Wiring the ISD1820 module
The module's own buttons still work alongside the pins. Do not connect either speaker terminal to GND.
| ISD1820 module pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5V | 3V3 |
| GND | GND | GND |
| REC | D2 | GPIO 25 |
| PLAYE | D3 | GPIO 26 |
| SP+ / SP- | 8 ohm speaker | 8 ohm speaker |
- VCC
- Arduino Uno:
- 5V
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- REC
- Arduino Uno:
- D2
- ESP32:
- GPIO 25
- PLAYE
- Arduino Uno:
- D3
- ESP32:
- GPIO 26
- SP+ / SP-
- Arduino Uno:
- 8 ohm speaker
- ESP32:
- 8 ohm speaker
Example code
Trigger PLAYE from a sensor instead, for example the PIR motion sensor, to make a talking greeter.
const int REC = 2, PLAY = 3;
void setup() {
pinMode(REC, OUTPUT);
pinMode(PLAY, OUTPUT);
digitalWrite(REC, HIGH); // record while HIGH
delay(5000);
digitalWrite(REC, LOW);
}
void loop() {
digitalWrite(PLAY, HIGH); // a short pulse plays the message
delay(50);
digitalWrite(PLAY, LOW);
delay(10000);
}Setup and tuning
speak 10 to 20 cm from the on-board mic for a clear message.
a larger ROSC resistor gives longer recording but lower quality.
recording past the limit just stops.
use the speaker supplied or a small 8 ohm speaker; it is not loud.
What you need
Shop this list5 of 7 found in our store · ₹518
ISD1820 Voice Recorder Module with On-Board Mic & 8Ω Speaker: the part this guide coversISD1820 Voice Recorder Module with On-Board Mic & 8Ω Speaker₹144
ISD1820 Voice Recording Module with Onboard Mic & Speaker Output: another version this guide coversISD1820 Voice Recording Module with Onboard Mic & Speaker Output₹141
ISD1820 Voice Recording Module with Speaker Support – 10-20s Audio Playback: another version this guide coversISD1820 Voice Recording Module with Speaker Support – 10-20s Audio Playback₹142- Uno R3 development board: the controller used in the wiring tableFind this part
Mini speaker 8 ohm: to hear the soundMini Speaker 8Ω₹42- PIR motion sensor HC-SR501: to play the message when someone walks pastFind this part
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- DFPlayer Mini: plays many MP3 files from a microSD card, much better quality.
- Voice modules: voice recognition and playback modules.
- MAX98357 I2S amplifier: play any audio from an ESP32.
Common mistakes to avoid
- Expecting several messages: the ISD1820 stores only one.
- Holding PLAYE expecting it to stop: use PLAYL for press-and-hold playback.
- Connecting a speaker terminal to GND.
- Recording far from the mic, which gives a quiet, noisy message.
Frequently asked questions
How long can the ISD1820 record?
About 10 seconds as supplied; changing the ROSC resistor gives 8 to 20 seconds.
Does it keep the message without power?
Yes, the message stays stored after power is removed.
Can an Arduino control it?
Yes, drive REC and PLAYE pins HIGH from digital outputs.
Can it store more than one message?
No. Use a DFPlayer Mini for several sounds.
Can I make it louder?
Feed the speaker output into a small amplifier such as the PAM8403 through a capacitor.
Parts for this guide
Projects that use it
Put this into practice: 56 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


