Buying guide · Beginner · 3 min read
Choosing a Speaker
Impedance, Power and Size
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
Match the speaker's impedance (usually 4 or 8 Ω) to what your amplifier supports, and choose a power rating at or above the amplifier's output. Higher sensitivity, in dB at 1 W and 1 m, means louder sound from the same power. A box or enclosure adds a lot of bass. Never drive a speaker straight from a GPIO pin; use an amplifier module or at least a transistor.
Key specs at a glance
- Impedance
- 4 Ω or 8 Ω typical for small speakers
- Power (RMS)
- 0.5 to 5 W for project speakers; peak ratings are higher and less useful
- Sensitivity
- dB SPL at 1 W, 1 m; 3 dB more is like doubling the power
- Size
- 28 to 40 mm for voice prompts, 50 to 100 mm for music
- Matching amps
- PAM8403 (3 W into 4 Ω at 5 V), DFPlayer (about 3 W), MAX98357A I2S
- Enclosure
- A sealed or ported box greatly improves bass
Impedance and power in practice
A lower-impedance speaker draws more current, so a 5 V class-D amp such as the PAM8403 gives about 3 W into 4 Ω but less into 8 Ω. Using a speaker below the amplifier's minimum impedance overheats it. Two 8 Ω speakers in parallel make 4 Ω; in series they make 16 Ω.
Pick a speaker rated for at least the amplifier's maximum output. Speakers more often fail from a clipping, distorted signal than from clean power, so keep the volume below the point where it distorts.
Which speaker for which project
| Project | Speaker | Driver |
|---|---|---|
| Beeps and simple tones | Buzzer or 0.5 W 8 Ω mini speaker | Transistor or buzzer module |
| Voice prompts, MP3 | 1 to 3 W, 4 or 8 Ω, 40 to 50 mm | DFPlayer Mini or PAM8403 |
| Internet radio, ESP32 audio | 3 W 4 Ω full-range | MAX98357A I2S amplifier |
| Music, Bluetooth speaker | 5 to 10 W per channel in a box | TPA3116 or similar class-D board |
- Beeps and simple tones
- Speaker:
- Buzzer or 0.5 W 8 Ω mini speaker
- Driver:
- Transistor or buzzer module
- Voice prompts, MP3
- Speaker:
- 1 to 3 W, 4 or 8 Ω, 40 to 50 mm
- Driver:
- DFPlayer Mini or PAM8403
- Internet radio, ESP32 audio
- Speaker:
- 3 W 4 Ω full-range
- Driver:
- MAX98357A I2S amplifier
- Music, Bluetooth speaker
- Speaker:
- 5 to 10 W per channel in a box
- Driver:
- TPA3116 or similar class-D board
Wiring rules
- A GPIO pin can supply only a few mA; driving a speaker directly can damage the pin. For tones, use a transistor with a series resistor, or a buzzer.
- Bridge-tied (BTL) amplifiers such as the PAM8403 and DFPlayer have outputs where neither side is ground. Connect the speaker across the two output pins only.
- Mount the speaker in a box, or at least on a baffle board, so sound from the back does not cancel the front.
Try it: dB converter calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Connecting a speaker straight to a GPIO pin.
- Grounding one side of a BTL amplifier output.
- Using a 4 Ω speaker on an amplifier rated for 8 Ω minimum.
- Running at full volume with distortion.
- Using a bare speaker with no enclosure and expecting bass.
Frequently asked questions
Should I use a 4 ohm or 8 ohm speaker?
Use what your amplifier supports. 4 Ω gives more volume from low-voltage class-D amps like the PAM8403; 8 Ω is safer on amps that do not list 4 Ω.
Can I connect a speaker directly to Arduino?
Not safely for anything but a tiny tone through a series resistor. Use a transistor or an amplifier module.
What does speaker sensitivity mean?
How loud it is with 1 W at 1 m. A speaker with 3 dB higher sensitivity sounds as loud as another with twice the power.
Why is my small speaker so quiet and tinny?
It has no enclosure. Mount it in a sealed box to improve volume and bass.
Can I connect two speakers to one amplifier channel?
Yes. Two 8 Ω in parallel make 4 Ω; check the amplifier supports 4 Ω first.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 56 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
- Diodes Inc. PAM8403 datasheet
- Analog Devices MAX98357A datasheet
- Speaker manufacturer Thiele-Small parameter data
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



