Double-clap light switch
Clap twice and the lights come on. Clap twice again to switch them off.
Shop by category
Shop all componentsA talking clock helps people with poor eyesight and older family members. Press the button and the Uno reads the clock module and plays recorded words: the hour, then the minutes, then morning, afternoon or evening. Because you record the clips yourself, it can speak Hindi, Tamil, Marathi or any language.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Plays MP3 files from a microSD card through its own small amplifier, on command from the board over serial.
Connects straight to SPK1 and SPK2 (the module has a small 3 W amplifier)
Follow the colours: red is power, dark grey is ground, blue is a signal.
talking_clock.inoVerify & upload in Electrolark// Talking clock for the visually impaired
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "talking-clock"
#include <Wire.h>
#include <RTClib.h>
#include <DFRobotDFPlayerMini.h>
#include <SoftwareSerial.h>
// ---- pins ----
const uint8_t MP3_RX = 2;
const uint8_t MP3_TX = 3;
const uint8_t BUTTON_PIN = 4;
RTC_DS3231 rtc;
DFRobotDFPlayerMini player;
SoftwareSerial mp3Serial(MP3_RX, MP3_TX);
const int VOLUME = 22;
// files on the card, in the mp3 folder: 0001-0012 = "one" to "twelve" (hours),
// 0100 = "o'clock", 0101-0159 = minutes "oh one" to "fifty-nine", 0200 = "in the morning", 0201 = "in the afternoon", 0202 = "in the evening"
bool wasDown = false;
void say(int track, int ms) { player.playMp3Folder(track); delay(ms); } // each clip is under a second
void setup() {
Serial.begin(115200);
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
pinMode(BUTTON_PIN, INPUT_PULLUP);
mp3Serial.begin(9600);
if (!player.begin(mp3Serial)) Serial.println(F("DFPlayer not found: check wiring and card"));
player.volume(VOLUME);
}
void loop() {
bool down = digitalRead(BUTTON_PIN) == LOW;
if (down && !wasDown) {
DateTime t = rtc.now();
int h = t.hour() % 12; if (h == 0) h = 12;
say(h, 900);
if (t.minute() == 0) say(100, 900); else say(100 + t.minute(), 1100);
say(t.hour() < 12 ? 200 : t.hour() < 17 ? 201 : 202, 1200);
Serial.print(t.hour()); Serial.print(':'); Serial.println(t.minute());
}
wasDown = down;
delay(20);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Check TX goes to the board RX pin and RX to the board TX pin, and that the card is inserted and FAT32.
Tracks are numbered by the order files were copied. Use the mp3 folder with 0001.mp3 names so the numbers are fixed.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
10 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, DS3231 Precision RTC Module with EEPROM, DFPlayer Mini MP3 Player Module (MP3-TF-16P), Tactile Push Button Switch, Mini Speaker 8Ω 1W 40mm, microSD Memory Card Class 10 (16GB), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (talking_clock.ino). Install these libraries first: RTClib and DFRobotDFPlayerMini.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,082 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Pull-ups and debouncing; Real-time clocks and backup batteries; Serial-controlled audio playback.
Ideas that reuse this build: Talking thermometer and RTC alarm clock. They are listed under Take it further on this page.
Clap twice and the lights come on. Clap twice again to switch them off.
Plays a friendly ding-dong whenever someone walks into the shop or room.
Beeps and flashes any message in Morse, or key your own by hand.
Turn a membrane keypad into a two-octave piano.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.