Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsThe LCD shows time and date on the top line and the alarm time below. Tap the button to move the alarm 5 minutes later; when it rings, tap to stop it until tomorrow.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
rtc_alarm_clock.inoVerify & upload in Electrolark// Alarm clock with LCD
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "rtc-alarm-clock"
#include <Wire.h>
#include <RTClib.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t BUZZER_PIN = 2;
const uint8_t BUTTON_PIN = 3;
RTC_DS3231 rtc;
LiquidCrystal_I2C lcd(0x27, 16, 2);
int alarmHour = 6;
int alarmMinute = 30;
bool ringing = false;
bool alarmDoneToday = false;
unsigned long lastDraw = 0;
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void draw(const DateTime& t) {
char line[17];
snprintf(line, sizeof(line), "%02d:%02d:%02d %02d/%02d", t.hour(), t.minute(), t.second(), t.day(), t.month());
lcd.setCursor(0, 0);
lcd.print(line);
snprintf(line, sizeof(line), "Alarm %02d:%02d %s", alarmHour, alarmMinute, ringing ? "WAKE" : " ");
lcd.setCursor(0, 1);
lcd.print(line);
}
void setup() {
Serial.begin(115200);
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
lcd.init();
lcd.backlight();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(BUTTON_PIN, INPUT_PULLUP);
}
void loop() {
DateTime t = rtc.now();
if (t.hour() == alarmHour && t.minute() == alarmMinute && !alarmDoneToday) ringing = true;
if (t.hour() == 0 && t.minute() == 0) alarmDoneToday = false;
if (digitalRead(BUTTON_PIN) == LOW) {
if (ringing) { ringing = false; alarmDoneToday = true; }
else { alarmMinute += 5; if (alarmMinute >= 60) { alarmMinute = 0; alarmHour = (alarmHour + 1) % 24; } } // tap to move the alarm by 5 min
delay(250);
}
setBuzzer(ringing && (millis() / 300) % 2 == 0);
if (millis() - lastDraw > 250) { lastDraw = millis(); draw(t); }
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Low-triggered module: invert the logic in setBuzzer().
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, DS3231 Precision RTC Module with EEPROM, LCD1602 16x2 Character LCD (blue, with I2C adapter), Active Buzzer Module 3.3–5V, Tactile Push Button Switch, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (rtc_alarm_clock.ino). Install these libraries first: RTClib and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹590 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Character displays and I²C backpacks; Pull-ups and debouncing; Real-time clocks and backup batteries.
Ideas that reuse this build: Simple 7-segment clock. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.