Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsEach face of the die is stored as eight bytes, one per row of the 8×8 matrix. Press the button and the faces flicker faster-to-slower like a real tumbling die before settling on a random result.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
64 red LEDs in an 8×8 grid driven by one MAX7219 chip over three wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
led_matrix_dice.inoVerify & upload in Electrolark// Electronic dice on an LED matrix
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "led-matrix-dice"
#include <LedControl.h>
// ---- pins ----
const uint8_t MX_DIN = 2;
const uint8_t MX_CS = 3;
const uint8_t MX_CLK = 4;
const uint8_t BUTTON_PIN = 5;
LedControl matrix(MX_DIN, MX_CLK, MX_CS, 1);
const byte FACES[6][8] = {
{0,0,0,0x18,0x18,0,0,0},
{0x03,0x03,0,0,0,0,0xC0,0xC0},
{0x03,0x03,0,0x18,0x18,0,0xC0,0xC0},
{0xC3,0xC3,0,0,0,0,0xC3,0xC3},
{0xC3,0xC3,0,0x18,0x18,0,0xC3,0xC3},
{0xDB,0xDB,0,0,0,0,0xDB,0xDB},
};
void showFace(int n) {
for (int row = 0; row < 8; row++) matrix.setRow(0, row, FACES[n][row]);
}
void setup() {
Serial.begin(115200);
matrix.shutdown(0, false);
matrix.setIntensity(0, 4);
matrix.clearDisplay(0);
pinMode(BUTTON_PIN, INPUT_PULLUP);
randomSeed(analogRead(A0) + micros());
showFace(5);
}
void loop() {
if (digitalRead(BUTTON_PIN) != LOW) return;
// tumble: faces flicker and slow down like a rolling die
for (int d = 30; d < 220; d += 20) {
showFace(random(6));
delay(d);
}
int roll = random(6);
showFace(roll);
Serial.print(F("Rolled ")); Serial.println(roll + 1);
while (digitalRead(BUTTON_PIN) == LOW) delay(10);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check DIN/CLK/CS order and use short wires.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, MAX7219 8x8 LED Matrix Module, Tactile Push Button Switch, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 7 steps.
No. This page has the complete, tested code (led_matrix_dice.ino). Install this library first: LedControl.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹413 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Pull-ups and debouncing; Shift-register style LED drivers.
Ideas that reuse this build: Reaction timer game. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Time, date and an alarm you set with one button.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.