Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsThe DS3231 keeps accurate time from a coin cell, even when the Nano is unplugged, and the TM1637 shows hours and minutes with a blinking colon. The first upload sets the time from your computer.
Tick anything you already have and the total updates.
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Bright 4-digit 7-segment display driven by two wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
rtc_digital_clock.inoVerify & upload in Electrolark// Digital clock with real-time clock
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "rtc-digital-clock"
#include <Wire.h>
#include <RTClib.h>
#include <TM1637Display.h>
// ---- pins ----
const uint8_t SEG_CLK = 2;
const uint8_t SEG_DIO = 3;
RTC_DS3231 rtc;
TM1637Display seg(SEG_CLK, SEG_DIO);
bool colon = true;
unsigned long lastTick = 0;
void setup() {
Serial.begin(115200);
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
seg.setBrightness(5);
seg.clear();
}
void loop() {
if (millis() - lastTick < 500) return;
lastTick = millis();
DateTime now = rtc.now();
colon = !colon; // blink the colon every half second
seg.showNumberDecEx(now.hour() * 100 + now.minute(), colon ? 0b01000000 : 0, true);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
CLK and DIO swapped; swap them.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), DS3231 Precision RTC Module with EEPROM, TM1637 4-Digit 7-Segment Display Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 7 steps.
No. This page has the complete, tested code (rtc_digital_clock.ino). Install these libraries first: RTClib and TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹432 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Multiplexed 7-segment displays; Real-time clocks and backup batteries.
Ideas that reuse this build: Add an alarm. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
Time, date and an alarm you set with one button.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.