Component guide · Beginner · 3 min read
12V Geared DC Motors (Johnson, Centre Shaft, Rectangular Gearbox, YS37-555)

Specs and Wiring
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These 12 V gear motors combine a DC motor with a metal or plastic gearbox, giving a fixed output speed from 10 to several hundred RPM. Johnson and YS37-555 types are side-shaft, the centre shaft type has the output in line with the motor, and the rectangular gearbox gives high torque at low speed. Drive them with a motor driver, never straight from an Arduino pin.
Key specs at a glance
- Voltage
- 12 V nominal (6 to 12 V usable)
- Speed
- 10 to 1000 RPM depending on gear ratio
- No-load current
- About 100 to 300 mA
- Stall current
- About 1 to 5 A depending on type
- Shaft
- 6 mm D-shaft on most
- Gearbox
- Metal gears (Johnson, centre shaft), plastic or metal (rectangular)
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Johnson Geared DC Motor 12V₹569
Option 2Centre Shaft DC Geared Motor 12V₹150
Option 3Rectangular Gearbox High-Torque DC Motor 12V₹1,174
Option 4YS37-555 12V DC Gear Motor₹597
What the 12V geared DC motor is
A geared DC motor is a brushed DC motor with a gearbox fixed to its front. The gearbox lowers the speed and multiplies the torque, which is what robot wheels, winches and turntables need.
Choose RPM from wheel diameter: speed (m/s) = RPM x pi x wheel diameter (m) / 60. Lower RPM means more torque.
Size the driver for stall current, not running current. A motor that runs at 300 mA can pull 3 A when it stalls or starts.
12V geared DC motor pinout
The pins on the 12V geared DC motor and what each one does.
| Pin | Function |
|---|---|
| Terminal + | Motor lead |
| Terminal - | Motor lead (swap to reverse) |
- Terminal +
- Motor lead
- Terminal -
- Motor lead (swap to reverse)
Wiring the 12V geared DC motor
Solder a 100 nF capacitor across the motor terminals to reduce electrical noise.
| 12V geared DC motor pin | Uno + MD10C | ESP32 + MD10C |
|---|---|---|
| Motor leads | Driver OUT1 / OUT2 | Driver OUT1 / OUT2 |
| Driver PWM / DIR | D5 / D4 | GPIO 25 / GPIO 26 |
| Driver supply | 12 V | 12 V |
- Motor leads
- Uno + MD10C:
- Driver OUT1 / OUT2
- ESP32 + MD10C:
- Driver OUT1 / OUT2
- Driver PWM / DIR
- Uno + MD10C:
- D5 / D4
- ESP32 + MD10C:
- GPIO 25 / GPIO 26
- Driver supply
- Uno + MD10C:
- 12 V
- ESP32 + MD10C:
- 12 V
Example code
A minimal sketch to check the part works.
const int PWM = 5, DIR = 4;
void setup() { pinMode(DIR, OUTPUT); }
void loop() {
int v = analogRead(A0) - 512; // centre = stop
digitalWrite(DIR, v > 0);
analogWrite(PWM, constrain(abs(v) / 2, 0, 255));
delay(20);
}Setup and tuning
size it for the stall current. Use a Cytron MD10C or BTS7960 for big 12 V motors and an L298N or TB6612FNG only for small ones.
use the matching L bracket or clamp and a coupler or hub for the 6 mm D shaft.
ramp the PWM up over 100 to 300 ms to cut start-up current spikes.
add a fuse on the battery line sized just above the total stall current you expect.
solder a 100 nF capacitor across the motor terminals.
What you need
Shop this list9 of 10 found in our store · ₹4,568
Johnson Geared DC Motor 12V: the part this guide coversJohnson Geared DC Motor 12V₹569
Centre Shaft DC Geared Motor 12V: another version this guide coversCentre Shaft DC Geared Motor 12V₹150
Rectangular Gearbox High-Torque DC Motor 12V: another version this guide coversRectangular Gearbox High-Torque DC Motor 12V₹1,174
YS37-555 12V DC Gear Motor: another version this guide coversYS37-555 12V DC Gear Motor₹597- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Cytron MD10C 10A motor driver: a simple PWM/DIR driver for 12 V gear motorsCytron MD10C 10A Single DC Motor Driver₹1,249Closest match, check the specs
L298N dual H-bridge motor driver module: a basic driver for small motorsL298N Dual H-Bridge Motor Driver Module₹128
SMPS power supply in metal enclosure (5/12/24 V): a 12 or 24 V supplySMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
16mm rotary potentiometer: a knob to set speed16mm Rotary Potentiometer (Linear)₹14Closest match, check the specs
Alternatives and when to choose them
- Encoder gear motors: with speed feedback.
- TT and BO motors: cheaper plastic.
- DC motors.
Common mistakes to avoid
- Choosing a driver by running current instead of stall current.
- Picking a high RPM motor for a heavy robot, so it cannot start moving.
- Driving the motor straight from an Arduino pin.
- Leaving the battery unfused.
Frequently asked questions
What RPM should I choose for a robot?
100 to 300 RPM with 65 to 100 mm wheels gives a robot that is fast enough but still has torque to climb and turn.
Can a 12 V gear motor run at 6 V?
Yes. It runs at about half the speed and with less torque, which is fine for testing.
Which motor driver do I need?
Pick one rated above the stall current: an MD10C or BTS7960 for big motors, an L298N or TB6612FNG for small ones.
Does it have an encoder?
No. For speed or position feedback choose an encoder gear motor, which has a Hall sensor disc on the back.
What is the shaft size?
Most have a 6 mm D-shaped shaft; check the listing, because some rectangular gearboxes use 8 mm.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

