Buying guide · Beginner · 3 min read
How to Choose a Motor for a Robot or Project
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
Choose by the motion you need. For wheels that just spin, use a DC gear motor. For an arm or flap that moves to an angle, use a servo. For precise positioning or repeatable steps, as in 3D printers, use a stepper. For high speed and efficiency, as in drones, use a brushless motor with an ESC. Then size torque and speed, and pick a driver and battery that can supply the stall current.
Key specs at a glance
- DC gear motor
- Continuous rotation, easy speed control, needs H-bridge for direction
- Servo
- 0 to 180° positioning with built-in feedback, three wires
- Stepper
- Precise open-loop steps, holding torque, needs a stepper driver
- BLDC
- Fast and efficient, needs an ESC or BLDC driver
- Key numbers
- Torque (kg·cm or N·m), speed (RPM), stall current, voltage
- Rule of thumb
- Run motors at about 25 to 50% of stall torque
Motor types compared
| Motor | Motion | Control | Driver | Typical uses |
|---|---|---|---|---|
| DC gear motor (BO, N20, 775) | Continuous | Speed by PWM, no position | L298N, TB6612FNG, DRV8833 | Robot cars, fans, pumps |
| DC motor with encoder | Continuous with feedback | Speed and distance | Motor driver + encoder input | Odometry robots, balancing bots |
| Hobby servo (SG90, MG996R) | 0 to 180° (or continuous) | Angle by pulse width | None or PCA9685 | Arms, grippers, steering, flaps |
| Stepper (NEMA 17, 28BYJ-48) | Steps | Position by counting steps | A4988, TMC2209, ULN2003 | 3D printers, CNC, camera sliders |
| BLDC | Continuous, fast | Speed | ESC or BLDC driver | Drones, e-bikes, high-speed spindles |
| Linear actuator / solenoid | Straight line | Extend or retract | H-bridge, MOSFET | Hatches, locks, valves |
- DC gear motor (BO, N20, 775)
- Motion:
- Continuous
- Control:
- Speed by PWM, no position
- Driver:
- L298N, TB6612FNG, DRV8833
- Typical uses:
- Robot cars, fans, pumps
- DC motor with encoder
- Motion:
- Continuous with feedback
- Control:
- Speed and distance
- Driver:
- Motor driver + encoder input
- Typical uses:
- Odometry robots, balancing bots
- Hobby servo (SG90, MG996R)
- Motion:
- 0 to 180° (or continuous)
- Control:
- Angle by pulse width
- Driver:
- None or PCA9685
- Typical uses:
- Arms, grippers, steering, flaps
- Stepper (NEMA 17, 28BYJ-48)
- Motion:
- Steps
- Control:
- Position by counting steps
- Driver:
- A4988, TMC2209, ULN2003
- Typical uses:
- 3D printers, CNC, camera sliders
- BLDC
- Motion:
- Continuous, fast
- Control:
- Speed
- Driver:
- ESC or BLDC driver
- Typical uses:
- Drones, e-bikes, high-speed spindles
- Linear actuator / solenoid
- Motion:
- Straight line
- Control:
- Extend or retract
- Driver:
- H-bridge, MOSFET
- Typical uses:
- Hatches, locks, valves
Sizing torque for robot wheels
A simple estimate for a wheeled robot on flat ground:
- 1Force needed = mass x acceleration + rolling resistance. For a 2 kg robot accelerating at 0.5 m/s² with rolling resistance of about 0.05 x weight: 2 x 0.5 + 0.05 x 2 x 9.81 = 2 N.
- 2Torque per wheel = force x wheel radius / number of driven wheels. With 3.25 cm (0.0325 m) wheels and two motors: 2 x 0.0325 / 2 = 0.033 N·m, about 0.33 kg·cm.
- 3Add margin for slopes, carpet and gearbox losses: multiply by 2 to 3, so pick motors with at least about 1 kg·cm of rated torque.
- 4Speed: wheel RPM = speed / (π x wheel diameter) x 60. For 0.5 m/s with 65 mm wheels: about 147 RPM.
The motor power and torque and wheel speed calculators do this for you.
Do not forget current and the driver
Every motor has a stall current (the current when blocked), often five to ten times its running current. The driver and battery must survive it, at least briefly. A BO motor may run at 150 mA but stall at 1 A; an MG996R servo can stall at 2.5 A. Choose a driver rated above the stall current, a battery that can deliver the total, and separate the motor supply from the microcontroller supply. See motor drivers and power an Arduino.
Example picks
two BO or TT gear motors, TB6612FNG or L298N driver, 2x 18650 pack.
N20 metal gear motors (300 to 600 RPM) with a TB6612FNG; see line follower robot.
MG996R servos for the base and shoulder, MG90S for the wrist and gripper, PCA9685 driver.
NEMA 17 stepper with TMC2209 for silent motion.
geared DC motors with encoders, or steppers.
Try it: Motor power torque calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Choosing by RPM only and ignoring torque.
- Sizing the driver to running current instead of stall current.
- Powering motors from the microcontroller's regulator.
- Using a servo where continuous rotation with speed control is needed.
- Expecting a stepper to know its position after it has skipped steps.
Frequently asked questions
Which motor is best for a robot car?
A DC gear motor such as a BO, TT or N20 motor with a dual H-bridge driver. Add encoders if you need to measure distance.
Servo or stepper for a robot arm?
Servos are simpler for small arms because they hold an angle by themselves. Steppers suit larger, more precise arms with proper drivers and homing.
How much torque do I need?
Estimate the force to move your robot, multiply by the wheel radius, divide by the number of driven wheels, and add a margin of two to three times.
What is stall current?
The current a motor draws when it is powered but cannot turn. Drivers and batteries must handle it.
Can I use a BLDC motor for a robot wheel?
Yes, with a sensored BLDC or FOC driver for smooth low-speed torque. Drone ESCs are poor at low speed.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




