Component guide · Intermediate · 3 min read
LDRobot STL27L, D100, D200, Orbbec SL450 Pulsar, Richbeam LakiBeam1

and Benewake VLS-H5 Underwater 2D LiDAR
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These 360 or 270 degree 2D LiDARs cover low-cost to industrial robots. The LDRobot STL27L is a 25 m DTOF LiDAR, and the D100 and D200 kits are low-cost triangulation sensors with USB adapters. The Orbbec SL450 Pulsar and Richbeam LakiBeam1 are IP65 industrial units with 270 degree scans and Ethernet. The Benewake VLS-H5 scans 360 degrees underwater.
Key specs at a glance
- Range
- 8 m (D100, D200), 25 m (STL27L, LakiBeam1), 45 m (SL450), 5 m underwater (VLS-H5)
- Field of view
- 360 degrees (LDRobot, VLS-H5), 270 degrees (SL450, LakiBeam1)
- Interface
- UART (LDRobot), Ethernet UDP (SL450, LakiBeam1)
- Supply
- 5 V (LDRobot), 12 V or more (industrial)
- Protection
- IP65 (SL450, LakiBeam1), IPX8 (VLS-H5)
- Software
- ROS / ROS 2 drivers from each maker
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1LDRobot STL27L DTOF 360 Degree Lidar₹17,450
Option 2LDRobot D100 Triangulation LiDAR – 360° Scanning, 0.15-8m Range, 6Hz₹5,999
Option 3LDRobot D200 Triangulation Lidar Sensor – 8m Range, 360° Scanning₹6,459
Option 4Orbbec SL450 dToF LiDAR Pulsar – 270° FoV, 45m Range, IP65, ROS SDK₹58,399
Option 5Richbeam LakiBeam1 270° Industrial Single-line 2D ToF LiDAR (25m, 12V, Ethernet UDP, IP65)₹44,119
Option 6Benewake VLS-H5 Underwater 360° Single-Line Scanning LiDAR – IPX8, UART, 5m Range₹27,039
What the LDRobot, Orbbec, Richbeam and underwater 2D LiDAR is
LDROBOT and industrial 2D LiDARs, such as the LD06, LD19 and STL-27L, spin a laser to scan a 360° plane for robot mapping, navigation and obstacle detection.
LDRobot sensors stream data continuously at 230400 or 921600 baud without commands, which makes them easy to read from an ESP32 as well as a Pi.
Ethernet LiDARs need a fixed IP on the host network card; set it before launching the driver.
LDRobot, Orbbec, Richbeam and underwater 2D LiDAR pinout
The pins on the LDRobot, Orbbec, Richbeam and underwater 2D LiDAR and what each one does.
| Pin | Function |
|---|---|
| 5 V, GND | Power (LDRobot) |
| TX | Data out |
| PWM | Speed control (optional) |
| Ethernet + power | Industrial models |
- 5 V, GND
- Power (LDRobot)
- TX
- Data out
- PWM
- Speed control (optional)
- Ethernet + power
- Industrial models
Wiring the LDRobot, Orbbec, Richbeam and underwater 2D LiDAR
Connect the LDRobot, Orbbec, Richbeam and underwater 2D LiDAR like this.
| LDRobot, Orbbec, Richbeam and underwater 2D LiDAR pin | LDRobot | Industrial (Ethernet) |
|---|---|---|
| LiDAR | USB adapter to Pi | Ethernet to Pi or PC |
| Power | 5 V | 12 to 24 V |
| Software | ldlidar_ros2 | Maker's ROS 2 driver |
- LiDAR
- LDRobot:
- USB adapter to Pi
- Industrial (Ethernet):
- Ethernet to Pi or PC
- Power
- LDRobot:
- 5 V
- Industrial (Ethernet):
- 12 to 24 V
- Software
- LDRobot:
- ldlidar_ros2
- Industrial (Ethernet):
- Maker's ROS 2 driver
Example code
A minimal sketch to check the part works.
git clone the ldlidar_stl_ros2 package into your workspace
colcon build
sudo chmod 666 /dev/ttyUSB0
ros2 launch ldlidar_stl_ros2 stl27l.launch.py
Open RViz2, add LaserScan on /scan, fixed frame base_laser.Setup and tuning
connect 5 V, GND and TX to a UART or USB adapter at the stated baud rate.
use the vendor ROS or ROS 2 driver to publish LaserScan data.
mount level at the robot's top, with a clear 360° view.
use slam_toolbox or Cartographer to build maps.
range drops in bright sun; industrial models handle it better.
What you need
Shop this list9 of 9 found in our store · ₹2,50,747
LDRobot STL27L DTOF 360 Degree Lidar: the part this guide coversLDRobot STL27L DTOF 360 Degree Lidar₹17,450
LDRobot D100 Triangulation LiDAR – 360° Scanning, 0.15-8m Range, 6Hz: another version this guide coversLDRobot D100 Triangulation LiDAR – 360° Scanning, 0.15-8m Range, 6Hz₹5,999
LDRobot D200 Triangulation Lidar Sensor – 8m Range, 360° Scanning: another version this guide coversLDRobot D200 Triangulation Lidar Sensor – 8m Range, 360° Scanning₹6,459
Orbbec SL450 dToF LiDAR Pulsar – 270° FoV, 45m Range, IP65, ROS SDK: another version this guide coversOrbbec SL450 dToF LiDAR Pulsar – 270° FoV, 45m Range, IP65, ROS SDK₹58,399
Richbeam LakiBeam1 270° Industrial Single-line 2D ToF LiDAR (25m, 12V, Ethernet UDP, IP65): another version this guide coversRichbeam LakiBeam1 270° Industrial Single-line 2D ToF LiDAR (25m, 12V, Ethernet UDP, IP65)₹44,119
Benewake VLS-H5 Underwater 360° Single-Line Scanning LiDAR – IPX8, UART, 5m Range: another version this guide coversBenewake VLS-H5 Underwater 360° Single-Line Scanning LiDAR – IPX8, UART, 5m Range₹27,039
Raspberry Pi 5 single board computer: to run ROS or Python for scanning LiDARRaspberry Pi 5 16GB RAM Single Board Computer₹36,169Closest match, check the specs
NVIDIA Jetson Orin Nano Super developer kit: to process point clouds and depthNVIDIA Jetson Orin Nano Super Developer Kit₹54,724
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Alternatives and when to choose them
- RPLIDAR: popular and well supported.
- YDLIDAR: wide range.
- Safety laser scanners: certified safety.
Common mistakes to avoid
- Mounting it tilted.
- Blocking part of the view.
- Wrong baud rate.
- Expecting full range in sunlight.
Frequently asked questions
How do I use the LD06 with ROS 2?
Install the LDROBOT driver and launch it to publish /scan.
What range do these LiDARs have?
About 12 m for LD06, 25 m for STL-27L.
Why does the map look distorted?
The LiDAR is tilted or the robot odometry is poor.
Can it work outdoors?
Yes, but sunlight reduces range on low-cost models.
Can I read it with Arduino?
Yes, but a Raspberry Pi or PC handles the data better.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
