Component guide · Beginner · 4 min read
LED Modules

Grove Red, Green and Blue LEDs, LilyPad LEDs, Crowtail Bright LED, DFRobot Piranha LED, Traffic Light and Indicator Modules, DIP 3-Colour LED and NeoPixel Stick
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
LED modules put an LED and its resistor on a small board with a standard connector, so you drive them straight from a digital pin. Grove, Crowtail and Gravity versions plug into a shield; LilyPad LEDs sew into fabric; the traffic light and indicator modules show status in colours. Check the supply voltage and whether the module has its own resistor.
Key specs at a glance
- Types
- Grove, Crowtail, Gravity, LilyPad, traffic light, indicator, DIP 3-colour, NeoPixel Stick
- Colours
- Red, green, blue, yellow, white, warm white, RGB
- Control
- Digital pin on or off, PWM for dimming
- Supply
- 3.3 V to 5 V on most modules
- Resistor
- On the module for Grove, Crowtail and indicator modules
- Sewable
- LilyPad LEDs for e-textiles
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Adafruit NeoPixel Stick - 8 x 5050 WWA White LEDs with Integrated Drivers₹1,093
Option 2LED Traffic Lights Signal Module / Digital Signal Output Traffic Light Module₹34
Option 3DIP 3 Color LED Module₹28
Option 4SeeedStudio Grove Green LED₹196
Option 5Elecrow Crowtail- Bright LED₹357
Option 6LED Indicator Light Signal Light Module Yellow₹37
What the LED modules (Grove, LilyPad, Crowtail, Gravity, traffic light and indicator modules) is
A plain LED needs a series resistor; most of these modules already include one, so you can connect a signal pin directly and set it high to light the LED. Indicator modules have three pins (signal, VCC, GND) and a bright LED for status lights, the traffic light module has red, yellow and green LEDs for crossings and demos, and the DIP 3-colour LED mixes colours with PWM.
LilyPad LEDs are small sewable parts with large pads, and the NeoPixel Stick is an addressable bar of eight RGB LEDs that needs a single data pin and a library. Always check whether a module is active high (HIGH turns it on) or active low in its notes.
LED modules (Grove, LilyPad, Crowtail, Gravity, traffic light and indicator modules) pinout
The pins on the LED modules (Grove, LilyPad, Crowtail, Gravity, traffic light and indicator modules) and what each one does.
| Pin | Function |
|---|---|
| VCC | 3.3 V or 5 V |
| GND | Ground |
| SIG / S | Digital pin: HIGH turns the LED on |
| R / G / B (RGB parts) | One pin per colour, or one data pin on NeoPixel parts |
- VCC
- 3.3 V or 5 V
- GND
- Ground
- SIG / S
- Digital pin: HIGH turns the LED on
- R / G / B (RGB parts)
- One pin per colour, or one data pin on NeoPixel parts
Wiring the LED modules (Grove, LilyPad, Crowtail, Gravity, traffic light and indicator modules)
For a bare LED add a 220 ohm resistor in series. Modules with a built-in resistor connect directly.
| LED modules (Grove, LilyPad, Crowtail, Gravity, traffic light and indicator modules) pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5V | 3V3 |
| GND | GND | GND |
| SIG | D9 (PWM) | GPIO 2 |
- VCC
- Arduino Uno:
- 5V
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SIG
- Arduino Uno:
- D9 (PWM)
- ESP32:
- GPIO 2
Example code
Use a PWM-capable pin (D9 on the Uno) if you want to fade the LED.
const int LED = 9; // PWM pin
void setup() {
pinMode(LED, OUTPUT);
}
void loop() {
digitalWrite(LED, HIGH); delay(500); // on
digitalWrite(LED, LOW); delay(500); // off
for (int v = 0; v <= 255; v += 5) { analogWrite(LED, v); delay(15); } // fade up
}Setup and tuning
if the module has no resistor, add 220 ohms in series for a 5 V supply.
run 3.3 V modules from 3.3 V on an ESP32 and 5 V modules from 5 V.
use a PWM-capable pin for dimming; plain digital pins only switch on and off.
use conductive thread for LilyPad LEDs and keep positive and negative traces apart.
What you need
Shop this list19 of 20 found in our store · ₹3,172
Adafruit NeoPixel Stick - 8 x 5050 WWA White LEDs with Integrated Drivers: the part this guide coversAdafruit NeoPixel Stick - 8 x 5050 WWA White LEDs with Integrated Drivers₹1,093
LED Traffic Lights Signal Module / Digital Signal Output Traffic Light Module: another version this guide coversLED Traffic Lights Signal Module / Digital Signal Output Traffic Light Module₹34
DIP 3 Color LED Module: another version this guide coversDIP 3 Color LED Module₹28
SeeedStudio Grove Green LED: another version this guide coversSeeedStudio Grove Green LED₹196
Elecrow Crowtail- Bright LED: another version this guide coversElecrow Crowtail- Bright LED₹357
LED Indicator Light Signal Light Module Yellow: another version this guide coversLED Indicator Light Signal Light Module Yellow₹37
LED Indicator Light Signal Light Module Red: another version this guide coversLED Indicator Light Signal Light Module Red₹37
LED Indicator Light Signal Light Module Blue: another version this guide coversLED Indicator Light Signal Light Module Blue₹37
LED Indicator Light Signal Light Module Green: another version this guide coversLED Indicator Light Signal Light Module Green₹37
DFRobot Gravity: Digital Piranha LED Module - Blue: another version this guide coversDFRobot Gravity: Digital Piranha LED Module - Blue₹257
LilyPad LED Red Color (1pc): another version this guide coversLilyPad LED Red Color (1pc)₹28
10mm Light emitting Module Led Sensor LED Indicator Module Blue: another version this guide covers10mm Light emitting Module Led Sensor LED Indicator Module Blue₹78
LilyPad LED White Color: another version this guide coversLilyPad LED White Color₹17
LilyPad LED Yellow Color: another version this guide coversLilyPad LED Yellow Color₹28
LilyPad LED Warm White: another version this guide coversLilyPad LED Warm White₹38
LilyPad LED Normal Green Color: another version this guide coversLilyPad LED Normal Green Color₹27
SeeedStudio Grove Red LED: another version this guide coversSeeedStudio Grove Red LED₹247
SeeedStudio Grove Blue LED: another version this guide coversSeeedStudio Grove Blue LED₹207- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Alternatives and when to choose them
- WS2812B addressable LEDs: many controllable LEDs on one pin.
- LED strips: long runs of light.
- Panel meters: meter-style indicators.
Common mistakes to avoid
- Driving a bare LED without a series resistor.
- Using a non-PWM pin and expecting dimming.
- Powering a 3.3 V module from 5 V.
- Crossing conductive thread on LilyPad parts.
Frequently asked questions
Do these modules need a resistor?
Most modules already include one, but a bare LED needs about 220 ohms.
Can I dim them?
Yes, with analogWrite on a PWM-capable pin.
What is the traffic light module?
A board with red, yellow and green LEDs that you control with three pins.
Can LilyPad LEDs be washed?
Check the product notes; most are not designed for machine washing.
What is the NeoPixel Stick?
A bar of eight RGB LEDs controlled over one data pin with a library.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


