Buying guide · Beginner · 3 min read
LED Strips
12 V, 24 V, COB and RGB (Non-Addressable)
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
A plain LED strip has LEDs and resistors in short groups that run from 12 V or 24 V, and you can cut it at marked points. Single-colour and RGB strips are dimmed with PWM through a MOSFET, unlike addressable WS2812B strips which take data. COB strips give a smooth line with no dots. Plan power by current per metre, and feed long runs from both ends to avoid dim, discoloured far ends.
Key specs at a glance
- Voltages
- 5 V, 12 V and 24 V (24 V suits longer runs)
- Types
- SMD 2835 or 5050, COB (continuous line), RGB, RGBW, CCT
- Power
- Roughly 4.8 to 14.4 W per metre for common strips (check label)
- Cutting
- Only on marked lines, every 3 LEDs on 12 V SMD strips (varies)
- Dimming
- Low-side N-MOSFET PWM per channel
- Protection
- IP20 indoor, IP65 silicone coated, IP67/68 sleeved
Choosing a strip
- 12 V vs 24 V: at the same power, 24 V strips draw half the current, so the voltage drop along the strip is smaller and you can run longer lengths from one feed.
- SMD vs COB: SMD strips show separate dots unless diffused; COB strips put LEDs under a continuous phosphor line, ideal in shallow channels.
- Colour temperature: warm white is about 2700 to 3000 K, neutral about 4000 K and cool about 6500 K. A high CRI (90+) looks more natural on skin and food.
- IP rating: coated strips run warmer and are harder to solder. Use bare strips in an aluminium channel indoors.
- For effects with individual colours per LED, use addressable strips instead.
Dimming with a microcontroller
Strips draw too much current for a GPIO pin. Use one logic-level N-channel MOSFET per colour channel as a low-side switch: strip + to the 12 V supply, strip − (or R, G, B) to the MOSFET drain, source to ground, gate to a PWM pin through 100 Ω with a 10 kΩ pull-down. Join the supply ground and the board ground. RGB strips are common anode: the shared wire goes to +12 V and each colour is switched to ground.
Power and voltage drop
Multiply watts per metre by length and add about 20 % to size the supply: 5 m of 9.6 W/m is 48 W, so choose 60 W or more. Copper strips drop voltage along their length; feed long runs at both ends or every 5 m, using thick wire. Aluminium channels act as a heatsink and extend LED life. The LED strip power calculator does the sums.
Try it: LED strip power calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Cutting between the marked cut lines.
- Feeding a long 12 V run from one end only.
- Driving a strip directly from an Arduino pin.
- An undersized supply that overheats.
- Mixing up addressable and non-addressable strips.
Frequently asked questions
12 V or 24 V LED strip?
24 V for runs over a few metres, because lower current means less voltage drop.
Can I control a 12 V strip with Arduino?
Yes, through a logic-level MOSFET or a ready MOSFET module, using PWM to dim.
Why is the end of my strip dim or orange?
Voltage drop along the strip; add power at the far end.
What is a COB LED strip?
A strip with densely packed LEDs under a continuous phosphor coating, so it shows a smooth line without dots.
Can I join cut pieces?
Yes, with solder or clip connectors matched to the strip width and pad count.
Parts for this guide
- ₹419View
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

