Component guide · Beginner · 3 min read
LM2577 Adjustable Boost Converter Module

Setup and Wiring
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The LM2577 module is an older but robust adjustable boost converter. It raises 3.5 to 35 V inputs to a higher adjustable output, typically for small 12 V or 24 V loads from a lower supply. It switches at 52 kHz with a built-in 3 A switch, so it suits loads up to about 1 A at moderate boost ratios.
Key specs at a glance
- Input
- 3.5 to 35 V
- Output
- Input to about 35 V
- Switch current
- 3 A internal (input side)
- Output current
- About 0.5 to 1 A depending on ratio
- Frequency
- 52 kHz
- Efficiency
- About 80 to 88 percent
What the LM2577 boost converter is
The LM2577 is a step-up switching regulator chip from TI with a built-in 3 A switch. The module adds the inductor, diode and trimmer, so it raises a lower DC voltage to an adjustable higher one.
The LM2577 is less efficient than the XL6009 and MT3608 but has soft-start and current limiting built in, which makes it forgiving for motors and capacitive loads.
LM2577 boost converter pinout
The pins on the LM2577 boost converter and what each one does.
| Pin | Function |
|---|---|
| IN+ / IN- | Input |
| OUT+ / OUT- | Output |
| Trimmer | Output voltage |
- IN+ / IN-
- Input
- OUT+ / OUT-
- Output
- Trimmer
- Output voltage
Wiring the LM2577 boost converter
Set the output with a multimeter before connecting any load. Turn the trimmer slowly; many need 10 or more turns before the voltage moves.
| LM2577 boost converter pin | Arduino Uno | ESP32 |
|---|---|---|
| IN+ / IN- | Supply or battery | Supply or battery |
| OUT+ / OUT- | Arduino VIN or 5V | ESP32 5V (VIN) |
| Ground | Common with the controller | Common |
- IN+ / IN-
- Arduino Uno:
- Supply or battery
- ESP32:
- Supply or battery
- OUT+ / OUT-
- Arduino Uno:
- Arduino VIN or 5V
- ESP32:
- ESP32 5V (VIN)
- Ground
- Arduino Uno:
- Common with the controller
- ESP32:
- Common
Example code
A minimal sketch to check the part works.
1. Power the module with nothing on the output.
2. Measure OUT+ to OUT- with a multimeter.
3. Turn the trimmer until the reading is correct.
4. Connect the load and measure again under load.Setup and tuning
keep the output under about three times the input for useful current.
turn the trimmer with no load and a meter connected, then add the load.
input current ≈ output power ÷ 0.85 ÷ input voltage; keep it under about 2.5 A.
the chip and diode warm up near 1 A output; leave airflow around them.
add a 100 to 470 µF capacitor on the output for noise-sensitive loads.
What you need
Shop this list4 of 4 found in our store · ₹621
LM2577 Boost Converter Module: the part this guide coversLM2577 Boost Converter Module₹193
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
DC power adapter (5.5 x 2.1 mm): a wall adapter inputDC Power Adapter (5.5x2.1mm)₹188
XL6009 adjustable boost converter module: a common boost for up to about 2 AXL6009 Adjustable Boost Converter Module₹63
Alternatives and when to choose them
- XL6009 boost: more efficient.
- High-power boost: more current.
- MT3608 boost: tiny.
Common mistakes to avoid
- Expecting high current at large boost ratios.
- Setting the output below the input.
- Connecting the load before checking the voltage with a meter.
- Drawing more input current than the 3 A switch allows.
Frequently asked questions
What is the maximum output voltage of the LM2577 module?
About 35 V. The output must always be higher than the input.
How much current can the LM2577 give?
About 0.5 to 1 A, depending on how far you step up. The higher the boost, the lower the current.
Can it make 12 V from 5 V USB?
Yes, at a few hundred milliamps, which suits small 12 V fans, sensors or relays.
Why use the older LM2577 instead of a newer chip?
It switches at a lower frequency, so it is less efficient and larger, but it is very robust and tolerant of wiring mistakes.
Can it step down as well?
No. It is boost only. Use a buck-boost module if the input can go above the output.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
