Component guide · Beginner · 3 min read
micro:bit Expansion Boards

Cytron REKA:BIT Robotics Board, DFRobot micro:Driver and LEGO-Compatible micro:bit Holder
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
micro:bit expansion boards take the BBC micro:bit's edge connector and add what a robot needs. The Cytron REKA:BIT has two DC motor channels, four servo ports, Grove-style sensor ports, a buzzer and RGB LEDs, powered by batteries. The DFRobot micro:Driver drives DC motors, steppers and eight servos. The LEGO-compatible holder mounts a micro:bit on brick builds.
Key specs at a glance
- Connector
- micro:bit edge connector slot
- REKA:BIT
- 2 DC motors, 4 servos, 6 sensor ports, buzzer, 2 RGB LEDs
- micro:Driver
- 4 DC motors or 2 steppers, 8 servos, IR receiver
- Power
- AA or 18650 battery holders, power switch
- Programming
- MakeCode blocks with the maker's extension
- Holder
- LEGO Technic-compatible holes
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Cytron micro:bit Robotics Expansion Board₹3,457
Option 2DFRobot micro:Driver Expansion Board for micro:bit₹1,409
Option 3micro:bit Expansion Board Holder (LEGO-compatible)₹408
What the micro:bit expansion boards (Cytron REKA:BIT, DFRobot micro:Driver, LEGO-compatible holder) is
micro:bit expansion boards are edge-connector breakouts and robot boards that turn the BBC micro:bit's pins into easy headers, motor drivers, servo ports and Grove sockets.
Insert the micro:bit with its LED screen facing the right way (marked on the board). Add the board's MakeCode extension (search 'rekabit' or 'motor:bit/micro:Driver' in Extensions) to get motor and servo blocks.
Power motors from the batteries, not from the micro:bit's USB. Switch off before plugging in servos.
micro:bit expansion boards (Cytron REKA:BIT, DFRobot micro:Driver, LEGO-compatible holder) pinout
The pins on the micro:bit expansion boards (Cytron REKA:BIT, DFRobot micro:Driver, LEGO-compatible holder) and what each one does.
| Pin | Function |
|---|---|
| Edge slot | micro:bit pins P0-P20 |
| Motor terminals | M1, M2 (and more on micro:Driver) |
| Servo ports | Signal, V, G |
| Sensor ports | Grove-style on REKA:BIT |
| Battery input | Holder or terminal with switch |
- Edge slot
- micro:bit pins P0-P20
- Motor terminals
- M1, M2 (and more on micro:Driver)
- Servo ports
- Signal, V, G
- Sensor ports
- Grove-style on REKA:BIT
- Battery input
- Holder or terminal with switch
Wiring the micro:bit expansion boards (Cytron REKA:BIT, DFRobot micro:Driver, LEGO-compatible holder)
Use fresh batteries: weak cells make servos jitter and the micro:bit reset.
| micro:bit expansion boards (Cytron REKA:BIT, DFRobot micro:Driver, LEGO-compatible holder) pin | Connection | Note |
|---|---|---|
| micro:bit | Into the edge slot | Screen facing up as marked |
| Motor | M1 terminals | Swap wires to reverse |
| Servo | S1 header | Brown or black wire to G |
- micro:bit
- Connection:
- Into the edge slot
- Note:
- Screen facing up as marked
- Motor
- Connection:
- M1 terminals
- Note:
- Swap wires to reverse
- Servo
- Connection:
- S1 header
- Note:
- Brown or black wire to G
Example code
REKA:BIT and micro:Driver use an on-board controller, so their pins differ: use the maker's MakeCode extension for real projects.
# MakeCode blocks are the usual way. This MicroPython sketch shows the idea
# for boards that drive motors with plain PWM on two pins (check your board).
from microbit import *
def forward(speed=700):
pin1.write_analog(speed) # motor A
pin2.write_analog(speed) # motor B
def stop():
pin1.write_analog(0)
pin2.write_analog(0)
while True:
if button_a.was_pressed():
forward()
sleep(2000)
stop()Setup and tuning
slide the micro:bit into the edge connector with the LED side facing the way the board shows.
use the board's battery input for motors and servos; USB alone is too weak.
add the maker's MakeCode extension to get blocks for motors and sensors.
many pins are shared with the LED display and buttons; turn the display off to free them.
micro:bit pins are 3.3 V; use 3.3 V sensors or level shifting.
What you need
Shop this list4 of 4 found in our store · ₹5,323
Cytron micro:bit Robotics Expansion Board: the part this guide coversCytron micro:bit Robotics Expansion Board₹3,457
DFRobot micro:Driver Expansion Board for micro:bit: another version this guide coversDFRobot micro:Driver Expansion Board for micro:bit₹1,409
micro:bit Expansion Board Holder (LEGO-compatible): another version this guide coversmicro:bit Expansion Board Holder (LEGO-compatible)₹408
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- Arduino CNC and motor shields: Arduino versions.
- Pico add-on boards: Pico robot boards.
- PCA9685 servo driver: many servos.
Common mistakes to avoid
- Inserting the micro:bit the wrong way.
- Driving motors from USB power.
- Using display pins without turning the display off.
- Connecting 5 V signals.
Frequently asked questions
Which micro:bit pins are free to use?
P0, P1, P2, P8, P12 to P16 are often free; others share the LEDs and buttons.
How do I program the expansion board?
Add the maker's MakeCode extension and use its blocks or Python.
Can I drive motors from USB power?
No. Motors draw too much for USB, so use batteries through the board's power input.
Why do my LED display and sensor conflict?
They share pins; turn off the display in code.
Can I use 5 V sensors?
Only with level shifting; the micro:bit is a 3.3 V board.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
