Component guide · Beginner · 3 min read
230 V Microwave Motion Sensor Switches

5.8 GHz Ceiling, Batten and In-Line Radar Light Switches
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These sensors switch a 230 V light on when someone moves and off after a delay. They use 5.8 GHz microwave radar, so they can hide inside a light fitting or behind a plastic cover, and they work in hot rooms where PIR struggles. Ceiling units cover 360 degrees; the Moonlex batten has the sensor built in. Range, delay and light level are set with knobs or DIP switches.
Key specs at a glance
- Supply
- 100 to 240 V AC (check model)
- Frequency
- 5.8 GHz
- Range
- About 2 to 8 m radius, adjustable
- Delay
- About 10 s to several minutes
- Light level
- Daylight threshold adjustable
- Load
- See the rating; derate for LED drivers
This part is often wired to 230 V mains. Do all wiring with the plug pulled out, keep mains wires inside a closed box with strain relief, add a fuse, and never touch the board while it is plugged in. If you are new to mains wiring, have an electrician check it before you switch on.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 15.8G V05F Radar Motion Sensor AC100-240V – 360° Detection, 2-8m Range₹429
Option 25.8GD05Z Radar Motion Sensor AC220-240V – 360° Coverage, Flame-Retardant ABS₹449
Option 35.8GK01YZ Radar Motion Sensor AC220-240V – Ceiling Mount, 360° Coverage₹439
Option 45.8GY01BZ Radar Sensor AC220-240V – 5.8GHz Microwave Motion Detector, Ceiling Mount₹479
Option 5D08 5.8GHz Microwave Radar Motion Sensor AC220-240V – 360° Detection, Flame-Retardant ABS₹579
Option 6Moonlex BCSMS100 Motion Sensor Module 90-260V AC – Microwave Radar Switch₹255
What the Mains microwave motion sensor switches is
Microwave motion sensor switches are ready-made mains or low-voltage switches with a built-in radar that turn lights on when people move, used in corridors, stairs and bathrooms.
Radar switches see through plastic and thin walls, so set the range carefully or they will turn on for movement in the next room.
All wiring is at mains voltage: L in, N, and switched L out to the lamp. Fit them with the power off, inside an enclosure, and have an electrician do it if you are not qualified.
Mains microwave motion sensor switches pinout
The pins on the Mains microwave motion sensor switches and what each one does.
| Pin | Function |
|---|---|
| L | Mains live in |
| N | Mains neutral |
| L' / Load | Switched live to the lamp |
- L
- Mains live in
- N
- Mains neutral
- L' / Load
- Switched live to the lamp
Wiring the Mains microwave motion sensor switches
Mains only; no microcontroller connection. Use a smart radar module if you want data.
| Mains microwave motion sensor switches pin | Terminal | Connect to |
|---|---|---|
| L (live in) | Mains live (MCB protected) | Mains live |
| N | Mains neutral | Mains neutral |
| L' (load) | Lamp live | Lamp live |
- L (live in)
- Terminal:
- Mains live (MCB protected)
- Connect to:
- Mains live
- N
- Terminal:
- Mains neutral
- Connect to:
- Mains neutral
- L' (load)
- Terminal:
- Lamp live
- Connect to:
- Lamp live
Example code
These are stand-alone switches, so set-up is a walk test, not code.
1. Power off at the MCB.
2. Wire L, N and L' (load) as marked; tighten terminals.
3. Set range to minimum, delay to minimum, light level to maximum (works in daylight).
4. Power on and walk-test; raise range until the area is covered.
5. Set the delay you want, then turn the light level down to the dusk setting.Setup and tuning
mains versions connect live, neutral and load; they must be installed by a qualified electrician.
check the rated load in watts for LED, CFL or incandescent lamps.
set range, hold time and light level (daylight sensor) with the dials.
mount on ceilings or walls with a clear view; radar passes through thin covers.
keep away from moving fans or curtains.
What you need
Shop this list10 of 10 found in our store · ₹3,306
5.8G V05F Radar Motion Sensor AC100-240V – 360° Detection, 2-8m Range: the part this guide covers5.8G V05F Radar Motion Sensor AC100-240V – 360° Detection, 2-8m Range₹429
5.8GD05Z Radar Motion Sensor AC220-240V – 360° Coverage, Flame-Retardant ABS: another version this guide covers5.8GD05Z Radar Motion Sensor AC220-240V – 360° Coverage, Flame-Retardant ABS₹449
5.8GK01YZ Radar Motion Sensor AC220-240V – Ceiling Mount, 360° Coverage: another version this guide covers5.8GK01YZ Radar Motion Sensor AC220-240V – Ceiling Mount, 360° Coverage₹439
Generic 5.8GY01BZ Radar Sensor AC220-240V – 5.8GHz Microwave Motion Detector, Ceiling Mount: another version this guide covers5.8GY01BZ Radar Sensor AC220-240V – 5.8GHz Microwave Motion Detector, Ceiling Mount₹479
Generic D08 5.8GHz Microwave Radar Motion Sensor AC220-240V – 360° Detection, Flame-Retardant ABS: another version this guide coversD08 5.8GHz Microwave Radar Motion Sensor AC220-240V – 360° Detection, Flame-Retardant ABS₹579
Moonlex BCSMS100 Motion Sensor Module 90-260V AC – Microwave Radar Switch: another version this guide coversMoonlex BCSMS100 Motion Sensor Module 90-260V AC – Microwave Radar Switch₹255
Moonlex Motion Sensor Batten Light 10W 2ft – Microwave Motion Sensor, Wall Mountable: another version this guide coversMoonlex Motion Sensor Batten Light 10W 2ft – Microwave Motion Sensor, Wall Mountable₹366
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
5 V relay module with optocoupler: to switch a light or load5V Relay Module with Optocoupler₹74
HC-SR501 PIR motion sensor module: a PIR to compare or combine with radarHC-SR501 PIR Motion Detector Sensor Module₹59Closest match, check the specs
Alternatives and when to choose them
- PIR light switches: fewer false triggers.
- Microwave motion modules: low-voltage versions for projects.
- Presence radar: keeps lights on for still people.
Common mistakes to avoid
- Exceeding the LED load rating.
- Mounting near a fan.
- DIY mains wiring without training.
- Setting hold time too short.
Frequently asked questions
Can microwave sensors work through glass?
Yes. Microwaves pass glass, plastic and thin wood, but not metal.
What does the light-level dial do?
It stops the light from switching on when there is already enough daylight.
Why does the light stay on?
Hold time is long or something moves in range.
Can it switch LED lights?
Yes, as long as the total LED load stays within the switch's LED rating.
Can I install it myself?
Mains wiring should be done by a qualified electrician.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
