Component guide · Beginner · 3 min read
Nokia 5110 LCD

Pinout, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Nokia 5110 is an 84x48 pixel monochrome LCD from old Nokia phones, driven by the PCD8544 controller over SPI. It uses very little power, is readable in sunlight and has a backlight. The controller is a 3.3 V part, so use level shifting or series resistors with a 5 V Uno, and set the contrast in code.
Key specs at a glance
- Resolution
- 84 x 48 pixels, monochrome
- Controller
- Philips PCD8544
- Interface
- SPI (write only)
- Logic and supply
- 2.7 to 3.3 V
- Current
- Under 1 mA without backlight
- Backlight
- 4 LEDs, blue or white
What the Nokia 5110 LCD is
The Nokia 5110 display is a reflective LCD, so it stays readable in daylight and draws almost nothing without its backlight. It is a good choice for battery projects that need simple graphics, menus or a small game.
Text uses about 14 characters by 6 lines with the default font. For colour or higher resolution, see TFT displays.
Nokia 5110 LCD pinout
The pins on the Nokia 5110 LCD and what each one does.
| Pin | Function |
|---|---|
| RST | Reset |
| CE (SCE) | Chip enable (chip select) |
| DC | Data or command select |
| DIN | SPI data in (MOSI) |
| CLK | SPI clock |
| VCC | 3.3 V |
| BL (LIGHT) | Backlight (to GND or 3.3 V depending on board) |
| GND | Ground |
- RST
- Reset
- CE (SCE)
- Chip enable (chip select)
- DC
- Data or command select
- DIN
- SPI data in (MOSI)
- CLK
- SPI clock
- VCC
- 3.3 V
- BL (LIGHT)
- Backlight (to GND or 3.3 V depending on board)
- GND
- Ground
Wiring the Nokia 5110 LCD
With a 5 V Uno, put resistors in the signal lines as shown (or use a level shifter); the PCD8544 is a 3.3 V chip. With an ESP32 connect directly. Check whether your board's BL pin lights with GND or VCC.
| Nokia 5110 LCD pin | Arduino Uno | ESP32 |
|---|---|---|
| RST | D8 via 10k | GPIO 4 |
| CE | D7 via 1k | GPIO 5 |
| DC | D6 via 10k | GPIO 2 |
| DIN | D11 via 10k | GPIO 23 |
| CLK | D13 via 10k | GPIO 18 |
| VCC | 3.3V | 3V3 |
| GND | GND | GND |
- RST
- Arduino Uno:
- D8 via 10k
- ESP32:
- GPIO 4
- CE
- Arduino Uno:
- D7 via 1k
- ESP32:
- GPIO 5
- DC
- Arduino Uno:
- D6 via 10k
- ESP32:
- GPIO 2
- DIN
- Arduino Uno:
- D11 via 10k
- ESP32:
- GPIO 23
- CLK
- Arduino Uno:
- D13 via 10k
- ESP32:
- GPIO 18
- VCC
- Arduino Uno:
- 3.3V
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
Example code
Install Adafruit PCD8544 and Adafruit GFX. Contrast varies between panels, so adjust setContrast first if the screen looks blank or fully dark.
#include <Adafruit_GFX.h>
#include <Adafruit_PCD8544.h>
// CLK, DIN, DC, CE, RST
Adafruit_PCD8544 lcd(13, 11, 6, 7, 8);
void setup() {
lcd.begin();
lcd.setContrast(55); // try 40-70 until text is crisp
lcd.clearDisplay();
lcd.setTextSize(1);
lcd.println("Geekobot");
lcd.println("Nokia 5110");
lcd.drawRect(0, 30, 84, 18, BLACK);
lcd.display();
}
void loop() {}Setup and tuning
the most common 'blank screen' fix. Step setContrast from 40 to 70.
about 10 to 20 mA; add a resistor or PWM for dimming.
the pin order differs between red and blue boards; follow the labels on yours.
the library keeps a 504-byte frame buffer, fine for an Uno.
What you need
Shop this list4 of 5 found in our store · ₹538
Nokia 5110 LCD module (84x48): the display this guide coversNokia 5110 LCD Module (84x48)₹219- Uno R3 development board: the controller used in the wiring tableFind this part
4-channel logic level converter (BSS138): to connect 5 V and 3.3 V signals safely4-Channel Logic Level Converter (BSS138)₹20
Resistor assortment kit: for series resistors on 5 V boardsResistor Assortment Kit₹250
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- OLED SSD1306: sharper, self-lit, I2C, but not readable in direct sun.
- ST7735 TFT: colour graphics.
- 16x2 LCD: text only, larger characters.
Try it: Display framebuffer calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Driving it with 5 V signals directly.
- Not setting contrast and assuming the display is dead.
- Powering VCC from 5 V.
- Following a wiring diagram for a different board colour.
Frequently asked questions
Is the Nokia 5110 5 V tolerant?
Not officially. Use a level shifter or series resistors with 5 V boards.
Why is my screen blank?
Usually contrast. Try setContrast values from 40 to 70, and check RST and CE wiring.
Can it show images?
Yes, monochrome 84x48 bitmaps.
Does it work with ESP32?
Yes, directly at 3.3 V using the SPI pins.
How much power does it use?
Under 1 mA without the backlight, which makes it good for battery builds.
Is it readable in sunlight?
Yes. It is a reflective LCD.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

