Component guide · Beginner · 3 min read
PWM Solar Charge Controllers (10A with Timer, 20A)

12V and 24V Setup
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A PWM solar charge controller connects a solar panel to a 12 V or 24 V battery and stops overcharging. It also has a load output that switches off at low battery and can run as a dusk-to-dawn or timer light controller. The 10 A version suits about 120 W of panels at 12 V and the 20 A version about 240 W.
Key specs at a glance
- System
- 12 V or 24 V auto
- Current
- 10 A or 20 A
- Battery types
- Lead-acid (sealed, gel, flooded); some lithium settings
- Load output
- Low-voltage disconnect, light/timer modes
- Display
- LCD with settings
- USB
- 5 V USB on many
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Solar Charge Controller₹329
Option 2Solar Charge Controller with Timer 10A₹327
What the PWM solar charge controller is
A PWM solar charge controller connects a solar panel to a 12 or 24 V battery, regulates charging and switches a DC load, for small off-grid lights, pumps and cameras.
Always connect the battery first, then the panel, then the load. Disconnect in reverse. The controller detects 12 or 24 V from the battery at start-up.
PWM controllers need a panel voltage close to the battery voltage (a '12 V' 36-cell panel for a 12 V battery).
PWM solar charge controller pinout
The pins on the PWM solar charge controller and what each one does.
| Pin | Function |
|---|---|
| Solar + / - | Panel |
| Battery + / - | Battery |
| Load + / - | DC load |
- Solar + / -
- Panel
- Battery + / -
- Battery
- Load + / -
- DC load
Wiring the PWM solar charge controller
Connect the PWM solar charge controller like this.
| PWM solar charge controller pin | Home light | Street light |
|---|---|---|
| Battery | 12 V battery (connect first) | Same |
| Solar | 12 V panel | Same |
| Load | 12 V LED lights | Street light with timer |
- Battery
- Home light:
- 12 V battery (connect first)
- Street light:
- Same
- Solar
- Home light:
- 12 V panel
- Street light:
- Same
- Load
- Home light:
- 12 V LED lights
- Street light:
- Street light with timer
Example code
A minimal sketch to check the part works.
1. Connect the battery first, then the input source.
2. Measure charge voltage at the battery terminals.
3. Watch cell temperature during the first full charge.Setup and tuning
connect the battery first, then the panel, then the load; disconnect in reverse.
use a panel whose nominal voltage matches the battery (a 12 V panel with about 18 V Vmp for a 12 V battery).
pick a controller rated above the panel's short-circuit current with margin.
set lead-acid, gel or lithium mode correctly; wrong settings shorten battery life.
add fuses near the battery on both the battery and load wires.
What you need
Shop this list3 of 3 found in our store · ₹833
Solar Charge Controller: the part this guide coversSolar Charge Controller₹329
Solar Charge Controller with Timer 10A: another version this guide coversSolar Charge Controller with Timer 10A₹327
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
Common mistakes to avoid
- Connecting the panel before the battery.
- Choosing the wrong battery type setting.
- Leaving out fuses.
- Using a high-voltage panel with PWM.
Frequently asked questions
What is the difference between PWM and MPPT controllers?
PWM pulls the panel down to battery voltage; MPPT converts extra voltage into current and gets 10 to 30 % more energy.
Why must I connect the battery first?
The controller detects 12 or 24 V from the battery; connecting the panel first can damage it or set the wrong system voltage.
Can I use a 24 V panel on a 12 V battery with PWM?
It works but wastes much of the panel's power; use MPPT for that.
Can it charge lithium batteries?
Only controllers with a lithium mode or adjustable voltages; check the settings.
Why does the load output switch off?
Low-voltage disconnect protects the battery; recharge it or check the setting.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
