Buying guide · Beginner · 3 min read
AA, 9 V, NiMH and Lead-Acid Batteries for Projects
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
Alkaline AA cells give 1.5 V and are cheap but sag under heavy load. NiMH rechargeables give 1.2 V and handle motors far better. 9 V PP3 batteries hold little energy and suit only low-current circuits. Sealed lead-acid batteries are heavy but simple and safe for 12 V projects, while lithium primary cells such as the ER34615 last for years at tiny currents.
Key specs at a glance
- Alkaline AA
- 1.5 V nominal, about 2000 to 3000 mAh at low current, much less at high current
- NiMH AA
- 1.2 V, about 1900 to 2500 mAh, recharge hundreds of times
- 9 V PP3 alkaline
- About 400 to 600 mAh; poor for motors
- Sealed lead-acid 12 V
- Charge at about 14.4 V (cycle) or 13.6 V (float); do not discharge below about 10.5 V
- Lithium primary (Li-SOCl2)
- 3.6 V, very high capacity, only small currents
- Holders
- 2, 3, 4 and 6 x AA; 4 x AA alkaline gives about 6 V, NiMH about 4.8 V
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
Which battery for which job
| Battery | Voltage | Strength | Weakness | Good for |
|---|---|---|---|---|
| Alkaline AA/AAA | 1.5 V (falls to 1.0 V) | Cheap, everywhere, long shelf life | Sags at high current | Remotes, clocks, low-power sensors |
| NiMH AA/AAA | 1.2 V (flat) | High current, rechargeable | Self-discharge unless low-self-discharge type | Robot cars, toys, servos |
| 9 V PP3 | 9 V | Small, convenient | Little energy | Multimeters, smoke alarms, tiny circuits |
| Sealed lead-acid | 12 V (6 cells) | Robust, easy to charge | Heavy | UPS, alarms, solar test rigs |
| Lithium primary | 3.6 V | Huge capacity, 10+ year life | Low current, not rechargeable | Meters, data loggers |
- Alkaline AA/AAA
- Voltage:
- 1.5 V (falls to 1.0 V)
- Strength:
- Cheap, everywhere, long shelf life
- Weakness:
- Sags at high current
- Good for:
- Remotes, clocks, low-power sensors
- NiMH AA/AAA
- Voltage:
- 1.2 V (flat)
- Strength:
- High current, rechargeable
- Weakness:
- Self-discharge unless low-self-discharge type
- Good for:
- Robot cars, toys, servos
- 9 V PP3
- Voltage:
- 9 V
- Strength:
- Small, convenient
- Weakness:
- Little energy
- Good for:
- Multimeters, smoke alarms, tiny circuits
- Sealed lead-acid
- Voltage:
- 12 V (6 cells)
- Strength:
- Robust, easy to charge
- Weakness:
- Heavy
- Good for:
- UPS, alarms, solar test rigs
- Lithium primary
- Voltage:
- 3.6 V
- Strength:
- Huge capacity, 10+ year life
- Weakness:
- Low current, not rechargeable
- Good for:
- Meters, data loggers
Charging rules
use a NiMH charger that stops on a voltage drop or temperature rise. Never put alkaline cells in a charger; they can leak or burst.
charge with a constant-voltage charger limited to about 0.25 C (about 0.3 A for a 1.3 Ah battery), at about 14.4 V for cyclic use or 13.6 V to keep it on float. Store it charged; a flat lead-acid battery sulphates and loses capacity.
not rechargeable.
For rechargeable lithium cells see lithium batteries, and for coin cells see coin cells.
Designing with them
Count cells for the voltage you need. Four alkaline AAs start at about 6.4 V and fall to about 4 V, so an Arduino on its 5 V pin would see too much when fresh and too little near the end; feed them through a regulator or use a boost converter for steady 5 V. Six NiMH cells give 7.2 V, a good motor supply for robot cars. Avoid 9 V PP3 batteries for motors or Wi-Fi boards; they run flat in minutes. Estimate run time with the battery life calculator.
Try it: Battery life calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Charging alkaline cells.
- Powering motors from a 9 V PP3 battery.
- Mixing old and new cells, or different types, in one holder.
- Leaving a lead-acid battery discharged for weeks.
- Feeding 4 fresh AA cells straight into a 5 V pin.
Frequently asked questions
Why does my robot stop working on AA batteries?
Alkaline cells sag under motor current. NiMH cells or a Li-ion pack hold their voltage much better.
Can I use NiMH instead of alkaline?
Usually yes. Each cell is 1.2 V instead of 1.5 V, so check the device still gets enough voltage.
How long does a 9 V battery last with Arduino?
Only a few hours on an Uno, because the board's regulator and LEDs waste current. Use AA packs or Li-ion instead.
How do I charge a 12 V sealed lead-acid battery?
Use a constant-voltage charger at about 14.4 V with the current limited to about a quarter of the Ah rating.
What is an ER34615 battery used for?
Long-life, low-current devices such as meters and loggers. It gives 3.6 V for years but cannot supply high current.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 56 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
- Energizer and Panasonic alkaline and NiMH datasheets
- Yuasa NP sealed lead-acid charging guide
- EVE ER34615 datasheet
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



