LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA capacitive soil sensor checks how damp the soil is. When it falls below 35 % the relay starts a small submersible pump, and it keeps pumping until the soil is back above 50 %. That gap (hysteresis) stops the pump chattering on and off.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Capacitive probe that measures soil moisture without exposed metal, so it does not corrode like resistive probes.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Pumps water from a jar or bucket into the pot
Follow the colours: red is power, dark grey is ground, blue is a signal.
The pump runs from its own 4×AA pack: pack + to relay COM, relay NO to pump +, pump − back to pack −.
auto_plant_watering.inoVerify & upload in Electrolark// Automatic plant watering system
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "auto-plant-watering"
// ---- pins ----
const uint8_t SOIL_PIN = A0;
const uint8_t RELAY_PIN = 2;
const int SOIL_DRY = 520; // reading in dry air: calibrate
const int SOIL_WET = 260; // reading in a glass of water: calibrate
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
int soilPct = 0;
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 35; // water when the soil is drier than this
const float HYSTERESIS = 15; // gap that stops rapid on/off switching
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void evaluate() {
if (!alertOn && soilPct < ALERT_LEVEL) alertOn = true;
else if (alertOn && soilPct > ALERT_LEVEL + HYSTERESIS) alertOn = false;
statusText = alertOn ? "WATERING" : "Moist";
}
void setup() {
Serial.begin(115200);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
soilPct = constrain(map(analogRead(SOIL_PIN), SOIL_DRY, SOIL_WET, 0, 100), 0, 100);
evaluate();
Serial.print(F("Soil="));
Serial.print(soilPct);
Serial.print(F("%"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setRelay(alertOn);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Calibrate: note the raw reading in dry air and in water, and put them in SOIL_DRY and SOIL_WET.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Capacitive Soil Moisture Sensor – 3.3V/5V Analog Output, 5V Relay Module with Optocoupler (1 channel), Mini Submersible Water Pump 3–6V with 1m tube, Battery Holder (AA), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (auto_plant_watering.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹663 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Calibrating an analog sensor with map(); Isolation, relays and switching higher-power loads.
Ideas that reuse this build: Add an OLED to show soil moisture, Monitor it from your phone and Run it from a solar panel. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Soil=82%, status=Moist
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.