Component guide · Beginner · 3 min read
ReadyToSky 30A 1-6S PWM Electronic Switch

Remote On/Off for Lights and Payloads
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
This electronic switch turns a high-current load on or off from a normal servo PWM signal. Connect it to a spare RC receiver or flight controller channel, and a switch on your transmitter can control lights, a spray pump, a buzzer or a payload release. It handles up to 30 A at 3.7 to 27 V (1S to 6S).
Key specs at a glance
- Voltage
- 3.7 to 27 V (1S to 6S)
- Current
- 30 A
- Control
- Servo PWM (above about 1500 us = on)
- Switch
- MOSFET, low side
- Signal
- 3-pin servo lead
- Weight
- A few grams
This part can carry many amps. Use wire thick enough for the current, put a fuse close to the battery, check that connectors are rated for the load and give drivers and motors room to cool. A short at these currents melts wires in seconds.
What the RC PWM electronic switch is
An RC PWM electronic switch reads a receiver channel and switches a load, such as lights, a pump or a release mechanism, on and off from your radio.
The switch cuts the negative side of the load. Do not join load negative to battery negative elsewhere, or it cannot switch off.
RC PWM electronic switch pinout
The pins on the RC PWM electronic switch and what each one does.
| Pin | Function |
|---|---|
| Signal lead | PWM in |
| Battery + / - | Power in |
| Load + / - | Switched output |
- Signal lead
- PWM in
- Battery + / -
- Power in
- Load + / -
- Switched output
Wiring the RC PWM electronic switch
Connect the RC PWM electronic switch like this.
| RC PWM electronic switch pin | RC receiver | Flight controller |
|---|---|---|
| Signal | Receiver channel | Pixhawk AUX output (RELAY or servo function) |
| Load | LED lights | Spray pump |
- Signal
- RC receiver:
- Receiver channel
- Flight controller:
- Pixhawk AUX output (RELAY or servo function)
- Load
- RC receiver:
- LED lights
- Flight controller:
- Spray pump
Example code
A minimal sketch to check the part works.
SERVOx_FUNCTION = 1 (RCPassThru) or relay function
Assign a transmitter switch to the channel.Setup and tuning
plug the signal lead into a receiver channel; connect the load to the switch output.
feed high-current loads from the battery, not the receiver rail.
set the radio channel to a switch so the PWM crosses the switching point (around 1500 µs).
stay within the switch's current rating.
add a flyback diode for pumps and solenoids.
What you need
Shop this list2 of 2 found in our store · ₹616
ReadyToSky 30A 1-6S PWM Electronic Switch 3.7-27V: the part this guide coversReadyToSky 30A 1-6S PWM Electronic Switch 3.7-27V₹439
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- Servo testers: to test the switch.
- MOSFET switch modules.
Common mistakes to avoid
- Overloading the switch.
- No flyback diode on motors.
- Powering big loads from the receiver.
- Channel endpoints not crossing the threshold.
Frequently asked questions
How do I control lights from my RC radio?
Plug an RC switch into a spare channel and assign that channel to a switch.
Why does the switch not turn on?
The channel does not cross the threshold; check endpoints.
Can it switch a water pump?
Yes, within its current rating, with a flyback diode.
Can I power the load from the receiver?
Only tiny loads; use the battery for anything bigger.
Can I use it with a flight controller?
Yes, on a servo output set to a switch function.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
