Component guide · Intermediate · 3 min read
RC Radio Accessories

RadioMaster AG01, AG01 Mini and AG01-Nano CNC Hall Gimbals, Pocket Colour Cases, 3D Stick Ends, Phone Holders, FS-i6S Bracket and Replacement Joysticks
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These parts upgrade or repair an RC radio. RadioMaster AG01 gimbals are CNC metal hall-sensor gimbals: the full size fits TX16S and Boxer, Mini fits TX12 and Zorro, and Nano fits the Pocket. Stick ends change feel and grip. Phone holders clip a phone to the radio for DJI or mission planning apps. Pocket cases change the radio's colour.
Key specs at a glance
- AG01
- Full size, TX16S and Boxer, hollow-shaft option for wiring
- AG01 Mini
- TX12 and Zorro
- AG01-Nano
- Sensor
- Hall effect, no wear contacts
- Stick ends
- M3 or M4 thread; check your radio
- Holders
- Clamp to the radio handle or neck strap lugs
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1RadioMaster AG01 CNC Hall Gimbal – Hollow Shaft₹15,609
Option 2RadioMaster AG01 CNC Hall Gimbals for TX16S & Boxer₹18,386
Option 3RadioMaster AG01 MINI CNC Hall Gimbals for TX12 & Zorro₹12,569
Option 4RadioMaster AG01-Nano Hall Effect Gimbals for Pocket₹9,679
Option 5RadioMaster Pocket Optional Color Cases – Blue₹1,739
Option 6RadioMaster Pocket Optional Color Cases – Charcoal₹1,739
What the RC radio accessories (AG01 hall gimbals, Pocket cases, stick ends, phone and radio holders) is
RC radio gimbals, cases and accessories include replacement hall-effect gimbals, stick ends, lanyards, carry cases and batteries for transmitters.
After fitting new gimbals, run the radio's stick calibration (EdgeTX: Radio Setup > Hardware > Calibration). Adjust spring tension and throttle ratchet or friction plate to taste.
Check the thread size before buying stick ends: many radios use M4, some smaller radios M3.
RC radio accessories (AG01 hall gimbals, Pocket cases, stick ends, phone and radio holders) pinout
The pins on the RC radio accessories (AG01 hall gimbals, Pocket cases, stick ends, phone and radio holders) and what each one does.
| Pin | Function |
|---|---|
| Gimbal connector | Small JST lead to the main board |
| Screws | Four per gimbal |
| Tension screws | Spring and throttle friction adjustment |
| Stick thread | M3 or M4 |
| Holder clamp | Handle or strap lugs |
- Gimbal connector
- Small JST lead to the main board
- Screws
- Four per gimbal
- Tension screws
- Spring and throttle friction adjustment
- Stick thread
- M3 or M4
- Holder clamp
- Handle or strap lugs
Wiring the RC radio accessories (AG01 hall gimbals, Pocket cases, stick ends, phone and radio holders)
Remove the battery before opening a radio. Keep track of tiny screws and springs.
| RC radio accessories (AG01 hall gimbals, Pocket cases, stick ends, phone and radio holders) pin | Connection | Note |
|---|---|---|
| Gimbal lead | Same socket as the old gimbal | Note the orientation |
| Battery | Out before opening the radio | Avoid shorts |
| Calibration | In the radio menu after fitting | Move sticks to all corners |
- Gimbal lead
- Connection:
- Same socket as the old gimbal
- Note:
- Note the orientation
- Battery
- Connection:
- Out before opening the radio
- Note:
- Avoid shorts
- Calibration
- Connection:
- In the radio menu after fitting
- Note:
- Move sticks to all corners
Example code
Menu names vary slightly between EdgeTX versions.
1. SYS > Hardware > Calibration.
2. Centre all sticks and pots, press Enter.
3. Move each stick and pot to all its limits, press Enter.
4. Check Outputs: each stick should reach -100 and +100 and centre at 0.
5. Re-check the Betaflight Receiver tab: centre 1500, ends about 1000 and 2000.Setup and tuning
check the gimbal fits your radio model and connector.
recalibrate sticks in the radio after replacing gimbals.
choose length and grip for thumb or pinch flying.
use the right cell type and charger.
store radios in cases to protect sticks and switches.
What you need
Shop this list13 of 13 found in our store · ₹66,006
RadioMaster AG01 CNC Hall Gimbal – Hollow Shaft: the part this guide coversRadioMaster AG01 CNC Hall Gimbal – Hollow Shaft₹15,609
RadioMaster AG01 CNC Hall Gimbals for TX16S & Boxer: another version this guide coversRadioMaster AG01 CNC Hall Gimbals for TX16S & Boxer₹18,386
RadioMaster AG01 MINI CNC Hall Gimbals for TX12 & Zorro: another version this guide coversRadioMaster AG01 MINI CNC Hall Gimbals for TX12 & Zorro₹12,569
RadioMaster AG01-Nano Hall Effect Gimbals for Pocket: another version this guide coversRadioMaster AG01-Nano Hall Effect Gimbals for Pocket₹9,679
RadioMaster Pocket Optional Color Cases – Blue: another version this guide coversRadioMaster Pocket Optional Color Cases – Blue₹1,739
RadioMaster Pocket Optional Color Cases – Charcoal: another version this guide coversRadioMaster Pocket Optional Color Cases – Charcoal₹1,739
RadioMaster Pocket Optional Color Cases – OrangeRX: another version this guide coversRadioMaster Pocket Optional Color Cases – Orange₹1,689
RadioMaster Pocket Optional Color Cases – Yellow: another version this guide coversRadioMaster Pocket Optional Color Cases – Yellow₹1,730
Generic 3D Transmitter Stick Ends – Red (1 Pair): another version this guide covers3D Transmitter Stick Ends – Red (1 Pair)₹319
Universal Mobile Phone Holder for Futaba, JR, FlySky, Walkera & DJI Phantom 3/4 Transmitter: another version this guide coversUniversal Mobile Phone Holder for Futaba, JR, FlySky, Walkera & DJI Phantom 3/4 Transmitter₹589
FlySky FS-i6S Transmitter Support Holder Mount Bracket – Black: another version this guide coversFlySky FS-i6S Transmitter Support Holder Mount Bracket – Black₹1,359
ReadyToSky Drone Remote Control Joystick – 1 Pair, Black & Red: another version this guide coversReadyToSky Drone Remote Control Joystick – 1 Pair, Black & Red₹422
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- RadioMaster radios: radios these fit.
- Choosing an RC transmitter: gimbal types explained.
- Compact FPV radios: other radios.
Common mistakes to avoid
- Skipping calibration.
- Wrong gimbal for the radio.
- Cheap cells.
- Transporting radios without a case.
Frequently asked questions
Why should I upgrade to hall-effect gimbals?
They have no wiper to wear, so they stay smooth and precise.
Do I need to calibrate after changing gimbals?
Yes. Run stick calibration in the radio menu after fitting new gimbals.
Which stick ends should I choose?
Longer stick ends suit pinch flying, and shorter ones suit thumb flying.
Can I use any 18650 cell in my radio?
Use quality cells of the stated type, with correct polarity.
Why does my stick drift?
Worn gimbal pots or missing calibration; recalibrate first, then replace the gimbal.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
